Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem1) A tension Q is maintained in cord shown as it passes over pulleys of diameter d.

(a.) Neglecting weight of the rod and pulleys, express magnitude of the force P corresponding to equilibrium in terms of Q, a, d, and theta.

(b) Knowing that Q = 10 lb, a = 5 in, d = 0.8 in, and, theta=30 degrees, find out the magnitude P.

1168_Cord.jpg

problem2)  A motor delivers 500 hp to the shaft. Which is tubular and has an outer diameter of 2 in. If it is rotating at 236 rad/s. Find out its largest inner diameter if allowable shear stress for the material is? allow = 25 ksi. 1 hp = 550 ft*lb/s

395_Motor.jpg

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93940

Have any Question? 


Related Questions in Mechanical Engineering

A sample containing 421 g of ar is enclosed in a container

A sample containing 42.1 g of Ar is enclosed in a container of volume 0.0885 L at 375 K. Calculate P using the ideal gas, van der Waals, and Redlich-Kwong equations of state. Based on your results, does the attractive or ...

Problem -a consider a one-component system consisting of

Problem - a. Consider a one-component system consisting of spherical bubbles of vapor inside a liquid, which is commonly observed as a liquid begins to boil. This is similar to the case considered in class in which liqui ...

1 calculate the following for the function fx e-3x - 2xa

1) Calculate the following for the function f(x) = e -3x - 2x. a. Calculate the derivation of the function by hand. Write a MATLAB function that calculates the derivative of this function and calculate the derivative at ...

An i-beam with the proportions shown is to be used as a

An I-beam with the proportions shown is to be used as a long column. There is a concern about buckling, so two reinforcing plates are to be welded along the length of the column. Two options for the resulting cross secti ...

1 a differential manometer is used to measure the pressure

1. A differential manometer is used to measure the pressure change caused by a flow constriction in a piping system as shown. Determine the pressure difference between points A and B in psi. Which section has the higher ...

Major assignment employment outlook reportin the groups

Major Assignment: Employment Outlook Report In the groups from your previous assignment, research the employment outlook for your future profession. Present your findings as a formal research report that academic advisor ...

Asignmentnote all dimensions are in mm unless stated

ASSIGNMENT Note: All dimensions are in mm unless stated otherwise. A steel frame is shown in Figure 1. The steel used is ASTM A572 Grade 50. It consists of two span and braced by an arrangement of trusses at the right si ...

The probability of a linear molecule being in a particular

The probability of a linear molecule being in a particular rotational level J depends on the temperature, and for J 7 0 there is a temperature Tmax at which the probability for that level reaches a maximum. Derive an exp ...

1 a beaker has the shape of a circular cone of diameter 7

1. A beaker has the shape of a circular cone of diameter 7 in and height 9 in. When empty, it weighs 14 oz; full of liquid, it weighs 70 oz. Find the density of the liquid in both SI and U.S. customary units. 2. Some exp ...

In a small generating system there are two generators in

In a small generating system, there are two generators in parallel. One of them is a synchronous generator, and the other, an IG. The common load is 3.0 kW with a power factor of 0.92. If the IG supplies only 1.0 kW of t ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro