Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: Describe the independent and dependent sources with the help of V-I characteristics.

problem 2: A pure inductance of 3 mH carries a current of the wave form shown in figure. Find out the voltage across Inductor VL(t) and sketch the same.

2488_voltage across inductor.jpg

problem 3: Find out the resistance between the terminals ‘A-B’ in the network shown in below figure.

21_electrical network.jpg

problem 4: By using loop analysis find out the current flowing via 5 ohms resistor.

222_loop analysis.jpg

problem 5: By using nodal analysis find the current flowing through 3 ohms resistor.

206_nodal analysis.jpg

problem 6: find out the RMS and average values of square wave form shown in figure below.

1417_RMS and average values.jpg

problem 7: A series circuit consisting of a 10 ohms resistor, a 100 µF capacitance and 10 mH inductance is driven by a 50 Hz AC voltage source of maximum value 100 V. find out the equivalent  impedance, current in the circuit.
 
problem 8: A parallel circuit having two branches, first branch consisting of 3 ohms resistor is in series with 12.7 mH inductor, second branch consisting of 1 ohm resistor in series with 3.18 mH is connected across 200 V, single phase, 50 Hz supply.

find out:

a) The resultant admittance.
b) Total current input.
c) The current in each branch.

problem 9: A voltage V = 50 ?00 V is applied to a series circuit consisting of fixed inductive reactance XL = 5 ohms and a variable resistance R. Sketch the admittance and current locus diagrams.
 
problem 10: A series RLC circuit has to be designed so that it has a band width of 320 Hz and inductance of the coil is 0.2H. It is has to resonate at 350Hz, determine the resistance of coil and capacitance of condenser. If the applied voltage is 150V, determine the voltage across capacitor and coil.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M93488

Have any Question? 


Related Questions in Electrical & Electronics

1 explain the self-consistency condition for waveguiding in

1. Explain the self-consistency condition for waveguiding in a dielectric slab waveguide. 2. Discuss the dependence of the number of propagating modes in a dielectric slab waveguide on the ratio of the thickness d of the ...

1 is the cutoff wavelength dependent on the dielectric in

1. Is the cutoff wavelength dependent on the dielectric in the waveguide? Is the cutoff frequency dependent on the dielectric in the waveguide? 2. What is guide wavelength? 3. Provide a physical explanation for the frequ ...

1 at what point on the surface of the circular cylinder in

1. At what point on the surface of the circular cylinder in a potential flow does the pressure equal the free-stream pressure? 2. For the velocity potentials given below, find the stream function and sketch the streamlin ...

For a line charge of uniform density 10-3 cm situated along

For a line charge of uniform density 10 -3 C/m situated along the z-axis between (0, 0, -1) and (0, 0, 1), obtain the series expression for the electric potential at the point (0, y, 0) by dividing the line charge into 1 ...

The grades of a group of 1000 students in an exam are

The grades of a group of 1000 students in an exam are normally distributed with a mean of 70 and a standard deviation of 10. A student from this group is selected randomly. a) Find the probability that his/her grade is g ...

1 describe the phenomenon of the bouncing back and forth of

1. Describe the phenomenon of the bouncing back and forth of transient waves on a transmission line excited by a constant voltage source in series with internal resistance and terminated by a resistance. 2. Discuss the v ...

Question 1 design a suitable double -layer lap winding for

Question 1) Design a suitable double -layer lap winding for a 6-pole dc armature with 18 slots and two coil sides per slot. Give values of front-pitch, brack-pitch and commutator pitch. Draw the developed diagram and sho ...

Afirst-order ltic system has a characteristic root lambda

A first-order LTIC system has a characteristic root λ = -10 4 . a. Determine T r , the rise time of its unit step input response. b. Determine the bandwidth of this system. c. Determine the rate at which the information ...

1 what does the word retarded in the terminology retarded

1. What does the word retarded in the terminology retarded magnetic vector potential refer to? Explain. 2. Discuss the application of the magnetic vector potential in the determination of the electromagnetic fields due t ...

1 considering the second hand on your watch to be a vector

1. Considering the second hand on your watch to be a vector, state its polarization. What is the frequency? 2. What is a phasor? 3. Is there any relationship between a phasor and a vector? Explain. 4. Describe the phasor ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro