Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem1) A manufacturer lists the specifications of a dynamic tension-compression load cell as follows:

Undamped natural frequency = 1000 Hz
Damping ratio = 0.707
Sensitivity = 10mV/lbf
Stiffness = 100,000 lbf/in

If a dynamic force as indicated in the Figure is applied to the load cell, Find out the steady-state output voltage as a function of time.

2444_Dynamic load.jpg

problem2) In the figure below, h = 86.1 meters. Compute the maximum energy per unit mass that the ideal turbine can extract from the water. Take the density of water to be 1000 kg/m3 and atmospheric pressure to be 101.325 kPa. Enter your answer in Joules to two decimal places.

2332_atmospheric pressure.jpg

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93889
  • Price:- $20

Guranteed 24 Hours Delivery, In Price:- $20

Have any Question? 


Related Questions in Mechanical Engineering

1 the pump shown in the figure delivers water at 59degf at

1. The pump shown in the figure delivers water at 59°F at a rate of 550 gal/min. The inlet pipe has an inside diameter of 5.95 in. and it is 10 ft long. The inlet pipe is submerged 6 ft into the water and is vertical. Es ...

Define prying action sketch an alternative joint diagram

Define prying action? Sketch an alternative joint diagram showing the effects of prying action Name at least two things the joint designer can do to reduce prying action? This and the following three questions are all in ...

Calculate the fraction of n2 molecules in a sample at 298 k

Calculate the fraction of N2 molecules in a sample at 298 K that have speeds less than 10.0ms -1 by integrating the Maxwell-Boltzmann distribution over the appropriate range of speeds (just writing the correct integral i ...

When choosing a bolting material we must consider its

When choosing a bolting material we must consider its affect on the clamping force to be created by those bolts in service. Name two important aspects of the clamping force which will be affected, in part at least, by th ...

Draw the moment diagram for the elbow-biceps-forearm-hand

Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment if the total weight w of the forearm and hand are included and are assumed to act at the mid ...

1 according to the equipartition principle what is the

1. According to the equipartition principle, what is the overall energy in J of one mole of water at 1000 K if translational, rotational, and vibrational degrees of freedom are considered? 2. How many equipartition degre ...

Name some of the problems created by incorrect torque how

Name some of the problems created by incorrect torque ? How much preload do we want, in general? How much torque versus initial preload can you expect to encounter when tightening a group of unlubricated, as received, st ...

Which is greater the tensile strength of a bolt or its

Which is greater, the tensile strength of a bolt or its stripping strength? Why? Where in the bolt would we find the maximum tensile stress? Where in a conventional nut? Define proof strength ? Compute the conventional t ...

1 a beaker has the shape of a circular cone of diameter 7

1. A beaker has the shape of a circular cone of diameter 7 in and height 9 in. When empty, it weighs 14 oz; full of liquid, it weighs 70 oz. Find the density of the liquid in both SI and U.S. customary units. 2. Some exp ...

Salt water containing 192 lbgal of salt flows at a fixed

Salt water containing 1.92 lb/gal of salt flows at a fixed rate of 2 gal/min into a 100-gal tank, initially filled with fresh water. The density of the incoming solution is 71.8 lb/ft 3 . The solution, kept uniform by st ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro