Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem1) The turbine shown in Figure given below develops 100 hp when the flowrate of water is 20ft^3/s. If all losses are negligible, find out:

(a) the elevation h

(b) the pressure difference across the turbine, and

(c) the flowrate expected if the turbine were removed.

1030_Turbine.jpg

problem2) A force P of magnitude 90 lb is applied to member ACE , that is supported by the friction less pin at D and by the cable ABE. As the cable passes over a small pulley at B, the tension might be assumed to be the same in portion AB and BE of the cable. For the case when a = 3, determine

(a) the tension in the cable,

(b) the reaction at D.

51_Cable.jpg

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93934
  • Price:- $30

Guranteed 24 Hours Delivery, In Price:- $30

Have any Question? 


Related Questions in Mechanical Engineering

The wrong size bolts were used to connect the flanges in

The wrong size bolts were used to connect the flanges in Problem 5.8, and when the torque is applied to flange B it rotates by 2 degrees (twisting shaft AB) before engaging flange C. Once flange C is engaged both B and C ...

A closed cylindrical tank of length l radius r and wall

A closed cylindrical tank of length L, radius R, and wall thickness t contains a liquid at pressure p. If a hole is suddenly made in the cylinder, determine a. How much the tank radius R changes b. How much the tank leng ...

A 15 m tall utility pole is located at a 40deg bend in a

A 15 m tall utility pole is located at a 40° bend in a set of power lines. The tension in each line is 15 kN, and due to sag of the lines, the tension forces act along directions 10° below horizontal. A guy wire has been ...

If you were using a full length centerline gage rod to

If you were using a full length, centerline, gage rod to measure DL, how much change would you expect to see at 2508F?  What DL from ‘‘before tightening'' would you expect to see at 2508F if you were using ultrasonics to ...

Name the two types of bolted joints and tell why theyre

Name the two types of bolted joints and tell why they're called that? What is the main mission of the bolts in any joint? What factor largely determines the behavior and life of a tensile joint? Why are bolted joints oft ...

A domestic food freezer maintains a temperature of - 15degc

A domestic food freezer maintains a temperature of - 15°C. The ambient air temperature is 30°C. If heat leaks into the freezer at the continuous rate of 1.75 kJ/s what is the least power necessary to pump this heat out c ...

What do we mean by the term torque reaction a right angle

What do we mean by the term torque reaction? A right angle nut runner is used to produce 500 ft-lb of torque on a bolt having a 7/8 -9 UNC thread. The tool is 18 in. long. How much reaction force, created by the reaction ...

1 a 1968 volkswagen sedan is driving over a 7300-ft-high

1. A 1968 Volkswagen sedan is driving over a 7300-ft-high mountain pass at a speed of v m/s into a headwind of W m/s. Compute the gage pressure in mPa at a point on the auto where the velocity relative to the auto is v - ...

The ground state 1s1 h atom has two hyperfine states f 0

The ground state 1s1 H atom has two hyperfine states, F = 0 and F = 1, which correspond to different relative orientations of the nuclear spin and electron spin. The transition between these two states has a wavelength o ...

You are asked to design a cylindrical scuba tank with a

You are asked to design a cylindrical scuba tank with a radius R = 16 cm to a pressure of p = 12.0 MPa at a factor of safety of 2.0 with respect to the yield stress. The relevant tabulated yield values for the steel of w ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen