Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Mechanical Engineering Expert

A distillation column, as shown in the figure to the right, is a device used to separate components with different volatilities. In a specific process, a distillation column is used to separate a feed stream containing 0.5300 mol ethanol/mol and 0.4700 mol water/mol into two product streams: an overhead stream that is ethanol-rich and a bottoms stream that is water-rich. Vapor containing 0.8070 mol ethanol/mol (and 0.1930 mol water/mol) leaves the top of the distillation column and enters a condenser, where the stream condenses completely into a liquid. This stream is then split; the reflux returns to the column and the overhead product leaves the process. The ratio of the flow rates of reflux to overhead product is given by the reflux ratio:

R= flow rate of reflux / flow rate of overhead product

and for this particular process, R = 1.21. Liquid leaving the bottom of the distillation column enters a reboiler, where a fraction of the stream is vaporized and returns to the distillation column as boilup, while the liquid fraction leaves the process as bottoms product. The composition of the boilup and the bottoms product streams are governed by the relative volatility, ?, of ethanol and water:

where yE is the mole fraction of ethanol in the vapor stream, yW is the mole fraction of water in the vapor stream, xE is the mole fraction of ethanol in the liquid stream, and xW is the mole fraction of water in the liquid stream. For this particular process ? = 10.575, and the ratio of ethanol leaving the reboiler in the boilup to ethanol leaving the reboiler in the bottoms product is 0.710. For a basis of 100 mol of feed, 64.85 mols of overhead product is produced. Given this basis, answer the following questions. Label the process flow diagram below. Label any quantities as \"unknown\" if they are not given or implied above. Do not leave any blank spaces. Variables names are given for reference later.

FEED, REFLUX, CONDENSER, OVERHEAD PRODUCT, BOIL UP, REBOILER, BOTTOM PRODUCTS

Given the basis, what is n6, the moles of bottoms product?

What is the mole fraction of ethanol in the bottoms product?

What is n2, the moles of vapor leaving the distillation column (before the condenser)?

What is y7, the mole fraction of ethanol in the boilup stream?

What is n7, the moles of boilup?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M91002627

Have any Question?


Related Questions in Mechanical Engineering

Alocate ten minutes for the presentationuse audio visual

Allocate ten minutes for the presentation Use audio / visual / technological supports / aids where appropriate Use a minimum of 3 properly referenced articles. THEMES PRESENTATION TOPIC MEMORY Discuss the three learning ...

Life cycle assessmentfor your chosen service eg white board

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

Fluid mechanics assignment - finite control volume analysis

Fluid Mechanics Assignment - Finite Control Volume Analysis and Dimensional Analysis Q1. The wind blows through a 7ft × 10ft garage door opening with a speed of 5 ft/s as shown in the figure. Determine the average speed, ...

1 explain the term critical equipment and provide two clear

1. Explain the term "critical equipment" and provide two clear examples of machinery which falls into this category on board a twin screw motor vessel. 2. Explain the process of Charpy lmpact Testing including sample mar ...

5star questions amp answers1a define heat treatment bname

5 STAR QUESTIONS & Answers 1. A) Define Heat treatment B) Name different types of heat treatment processes C) Write any 4 purposes of Heat treatment 2. Explain various Heat treatment processes 3. A) Compare Thermo plasti ...

Fluid mechanics assignment - viscous flow in pipesq1 as

Fluid Mechanics Assignment - Viscous Flow in Pipes Q1. As shown in the figure below, water "bubbles up" 3 in. above the exit of the vertical pipe attached to three horizontal pipe segments. The total length of the 0.75-i ...

Projectflow processing of liquor in a mineral refining

Project Flow Processing of Liquor in a Mineral Refining Plant The aim of this project is to design a flow processing system of liquor (slurry) in a mineral (aluminum) refining plant. Aluminum is manufactured in two phase ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As