Ask Question, Ask an Expert

+61-413 786 465

[email protected]

Ask Mechanical Engineering Expert

Engineering


Home >> Mechanical Engineering

A bandpass filter has a constant attenuation of 2 dB in its pass band between 1000 Hz and 2000 Hz. The filter is designed to operate with a 50 Ohm source and load. Below 1000 Hz and above 2000 Hz the filter attenuates signals. The slope of the filter frequency response outside the pass band is 18 dB per octave. You may assume that the frequency response of this filter is made up of three straight lines when plotted on a dB vs log frequency graph. The filter is placed between a signal generator and a 50 Ohm load resistor.

a. Make a sketch of the response of the bandpass filter from 500 Hz to 10 kHz. Use a dB scale on the vertical axis and a log frequency scale on the horizontal axis from 500 Hz to 2000 Hz. Insert numbers on the scale on each axis.

b. The output of the signal generator is a sine wave at a frequency of 1500 Hz. With the filter removed from the circuit the power dissipated in the resistor is 1.0 W = 0 dBW. What is the power (in dBW) dissipated in the resistor with the filter in place between the signal generator and load resistor?

c. The output of the signal generator is changed to a sine wave at a frequency of 500 Hz. The power level is not changed. What is the power (in dBW) dissipated in the resistor with the filter in place between the signal generator and load resistor?

d. The output of the signal generator is changed to a sine wave at a frequency of 2000 Hz. The power level is not changed. What is the power (in dBW) dissipated in the resistor with the filter in place between the signal generator and load resistor?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M91629028
  • Price:- $20

Priced at Now at $20, Verified Solution

Have any Question?


Related Questions in Mechanical Engineering

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

Mechanical engineering assignment task - solve the given

Mechanical Engineering Assignment Task - Solve the given problem. Task 1 - A spring with a one-turn loop of 40mm mean radius is formed from a round section of wire having 5 mm diameter. The straight tangential legs of th ...

Projectflow processing of liquor in a mineral refining

Project Flow Processing of Liquor in a Mineral Refining Plant The aim of this project is to design a flow processing system of liquor (slurry) in a mineral (aluminum) refining plant. Aluminum is manufactured in two phase ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

Assignment -q1 explain the difference between the

Assignment - Q1. Explain the difference between the metacentric height of a ship during 'Partially Afloat condition and 'Free Floating' condition; aid a sketch to support your answer. Q2. With the aid of sketches, explai ...

Materials behaviour from atoms to bridges assignment -

Materials Behaviour from Atoms to Bridges Assignment - Distributed loads and static equilibrium (Please note: you should show your steps with necessary figures) Q1. Two beam sections are jointed at C and supported at A b ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As

Follow Us

© Copyright 2013-14 mywordsolution.com All rights reserved