Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem1) A 3.27 m3 tank contains 100kg of nitrogen at 225 K. Compute pressure in the tank, using following:

a) the ideal-gas equation of state

b) the van der Waal equation of state

c) the Beattie-Bridgeman equation of state.

Compare your results with actual value at 2000 kPa (i.e., give % error for each answer).

problem2) A rigid, well insulated container, is outfitted with moveable but frictionless partition which separates two sides but allows conduction between two sides. One side has 1 kg of air, initially at 500 kPa, 350K and the other side has 3 kg of CO2 initially at 200 kPa, 450K. DeteFind out final temperature (K) and final pressure (kPa) of the complete system, assuming constant specific heats.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93945

Have any Question? 


Related Questions in Mechanical Engineering

On a certain day the barometric pressure at sea level is

On a certain day the barometric pressure at sea level is 30.1 in. Hg, and the temperature is 70°F. The pressure gage in an airplane in flight indicates a pressure of 10.6 psia, and the temperature gage shows the air temp ...

Project solve the 3-dimensional steady state heat transfer

PROJECT Solve the 3-dimensional, steady state heat transfer problem for a cartesian system either numerically or analytically. - If you use the numerical method, write a computer code using the finite difference method o ...

1 air at 70degf flows into a 10-ft3nbspreservoir at a

1. Air at 70°F, Flows into a 10-ft 3  reservoir at a velocity of 110 fps. If the reservoir pressure is 14 psig and the reservoir temperature 70°F, find the rate of temperature increase in the reservoir. Assume the incomi ...

1 according to the equipartition principle what is the

1. According to the equipartition principle, what is the overall energy in J of one mole of water at 1000 K if translational, rotational, and vibrational degrees of freedom are considered? 2. How many equipartition degre ...

Why do we often want to create the correct preload in the

Why do we often want to create the correct preload in the bolts when we assemble a joint? Under what conditions is correct preload relatively unimportant? Name at least three factors that can increase the stress in previ ...

A compute the intrinsic gate delay of the nmost given in

(a) Compute the intrinsic gate delay of the nMOST given in the above problem and also in section 661 at the biasing condition given above. (b) Compute the intrinsic power-delay product. (c) Does the load resistor increas ...

A water jet pump has an area ajnbsp 006 ft2nbspand a jet

A water jet pump has an area A j  = 0:06 ft 2  and a jet velocity v j  = 90 fps, which entrains a secondary stream of water having a velocity v s  = 10 fps in a constant-area pipe of total area A = 0.6 ft 2 . At section ...

Magnet wire is single-strand wire with a thin insulation

Magnet wire is single-strand wire with a thin insulation layer (of enamel, varnish, glass, etc.) to prevent short circuits. In a production facility, copper (E = 120 GPa, σ ys = 70 MPa) magnet wire is to be coated with v ...

The jaws of the bolt cutter shown are connected by two

The jaws of the bolt cutter shown are connected by two links AB. The cross-sectional area of each link is 750 mm 2 . (a) What average normal stress is induced in each link by the 90 N forces exerted on the handles? (b) T ...

Problem -a consider a one-component system consisting of

Problem - a. Consider a one-component system consisting of spherical bubbles of vapor inside a liquid, which is commonly observed as a liquid begins to boil. This is similar to the case considered in class in which liqui ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen