Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Consider the following linear differential equations:

a. y'' + 2y' - 3y = 0            y(0) = 1, y'(0) = 0

b. 2y'' - 5y' + 3y = 0          y(0) = 1, y'(0) = 1

c. y'' + 5y' - 6y = 0             y(0) = 1, y'(0) = -1

Perform the following tasks on each of the above:

i. Write the differential equation as a system of first order differential equations expressed in matrix form.

ii. For each system, find the equilibrium points.

iii. Find the solution to the homogeneous differential equation using the eigenvalues and eigenvectors of the system matrix.

2) Find the solution to the following dynamical system equations given below. Assume that

804_fig1.png

Also, determine the nature of the equilibrium point based on the eigenvalues and eigenvectors of the system

2465_fig2.png

3) Solve the following non-homogenous dynamical system equations using Laplace transform.

Recall that for:

x'(t) = Ax(t) + Bu(t)

X(x) = (sI - A)-1 {x(0) + BU(s)}

1229_fig3.png

4) Fill the following table of eigenvalue response type for linear autonomous homogenous second order system. Identify whether or not the system represented is a stable system name the type of equilibrium point according to: stable/unstable, node/spiral center saddle, etc. Verify your solution using PPLANE8 software.

Matrix and Eigenvalue Condition

Name of Response

               A =  [2  0; 0 6];          λ1 = -1 ; λ2 = -2

 

 A =  [-2  - 2; 0  -6];                  λ1  = -2 ; λ2 = -6

 

 A =  [3  -2;  4  -1];      λ1  =  1 + 2i ;  λ2  =  1 - 2i

 

A = [-3  2;  -4  1];       λ1  = -1 + 2i ; λ2  = - 1 - 2i

 

   A =  [-1  - 6;  -6  0];             λ1  =  2 ;  λ2  = -3

 

         A =  [0  -1; 1  0];            λ1  =  i ;  λ2  = -i

 

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M91709346
  • Price:- $70

Priced at Now at $70, Verified Solution

Have any Question?


Related Questions in Mechanical Engineering

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

Problem on shaft -assuming no frictional losses a torque of

Problem on Shaft - Assuming no frictional losses, a torque of T = 750lb·in is applied through the shaft of gear F in order to drive the roller chain at point B at a constant speed. The chain sprocket has a pitch diameter ...

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

Life cycle assessmentfor your chosen service eg white board

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

Alocate ten minutes for the presentationuse audio visual

Allocate ten minutes for the presentation Use audio / visual / technological supports / aids where appropriate Use a minimum of 3 properly referenced articles. THEMES PRESENTATION TOPIC MEMORY Discuss the three learning ...

Life cycle assessmentfor your chosen service eg white

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As