Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Mechanical Engineering Expert

1 A vapor power plant operates with water as the working fluid, passing through the cycle at a flow rate of 12 kg/s. In the condenser, at constant pressure of 7 kPa, the water goes from a quality of 90% to saturated liquid state. The condenser uses a flow of cooling water to remove the heat from the working fluid water - the cooling water enters at 20°C and leaves the condenser at 35°C. What is the flow rate of the cooling water in the condenser? You may assume that the cooling water is incompressible, and is at atmospheric pressure = 100 kPa.

2. Answer the following as True or False, with a brief explanation:

(a) The change of entropy of a closed system is the same for every process between two specified states.

(b) The entropy of a fixed amount of an ideal gas increases in every isothermal compression process where V2 < V1.

(c) Wmint. rev.=-iev*dp is valid all the time, not just in certain situations.

3. A vapor power cycle is developed based on the Carnot cycle - not the Rankine cycle. Water is the working fluid, and the cycle operates at steady state. Saturated liquid enters the boiler at 16 MPa, and saturated vapor enters the turbine. The pressure in the condenser is 8 kPa. The mass flow rate of steam entering the turbine is 120 kg/s.

find:

(a) the thermal efficiency

(b) the back work ratio (bwr)

(c) the net power developed

4. Air at 300 K and 100 kPa enters a compressor, operating at steady state, and is compressed adiabatically to 150 kPa. The power input per mass flow rate (Wm) is 42 kJ/kg. For this analysis, assume that the ideal gas law applies, and that the specific heat ratio k is 1.4. Determine:

(a) the rate of entropy production per mass flow rate in kJ/kg*K

(b) the isentropic efficiency of the compressor

5. What was the big deal about the tsunami in Japan in 2012 and its effect on the Fukushima Nuclear Power Plant?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M91010902

Have any Question?


Related Questions in Mechanical Engineering

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Question - truss structureconsider the three membered

Question - Truss Structure Consider the three membered planar truss structure shown in the figure below. All members of the truss have identical square cross-sectional area (A) of 25 mm x 25 mm, and Youngs Modulus (E) = ...

5star questions amp answers1a define heat treatment bname

5 STAR QUESTIONS & Answers 1. A) Define Heat treatment B) Name different types of heat treatment processes C) Write any 4 purposes of Heat treatment 2. Explain various Heat treatment processes 3. A) Compare Thermo plasti ...

Expansion processes of a perfect gasassignment1 attend the

Expansion Processes of a Perfect Gas Assignment: 1. Attend the laboratory class and complete the lab tests according to the supervisor's requirement. Students will not allowed to submit their report if they do not come t ...

Mechanical engineering assignment task - solve the given

Mechanical Engineering Assignment Task - Solve the given problem. Task 1 - A spring with a one-turn loop of 40mm mean radius is formed from a round section of wire having 5 mm diameter. The straight tangential legs of th ...

Materials behaviour from atoms to bridges assignment -

Materials Behaviour from Atoms to Bridges Assignment - Distributed loads and static equilibrium (Please note: you should show your steps with necessary figures) Q1. Two beam sections are jointed at C and supported at A b ...

Life cycle assessmentfor your chosen service eg white board

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

Life cycle assessmentfor your chosen service eg white

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

Structural mechanics questions -q1 a 150-lb bucket is

Structural Mechanics Questions - Q1. A 150-lb bucket is suspended from a cable on the wooden frame. Determine the resultant internal loadings on the cross section at D, and at E. Q2. The shaft is supported at its ends by ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As