+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1) Using Octave, create and test set of programming statements to generate fs  bandpass ranges (2fc -B)/m & 2fc + B)/(m+1)) along with minimum fs value (fs >=2B), and positioned sampled spectra for the following values and ranges of m and k:

B=5 MHz
fc = 16 MHz
m ranges from 1-6
k ranges from 1-6 for (Positioned Spectra)

Find out the optimum sampling rates, as applicable for each m value. Place the results in the neatly organized table in a word document. Make sure to include optimum sampling rate for each reasonable value of m in the table.

Plot your results, using Octave, showing each of the sampling frequencies. Include horizontal line indicating minimum fs.  Ensure to include labels and legends for your plot.  ex plot is shown below for fc = 20 MHz. You require to include the upper and lower sampling ranges as well as the positioned sampled spectra and fs .

Analyze results to summarize the findings and the recommendations on your findings. In your analysis ensure to discuss exactly how you find out the optimum sampling rates. For instance, how did you find out which spectral replication was located exactly at the baseband butting up against the zero HZ? Also, describe when the selected m values would cause aliasing and at what point fs  is no longer greater than or equal to the 2B.

Electrical & Electronics, Engineering

• Category:- Electrical & Electronics
• Reference No.:- M95672

Have any Question?

## Related Questions in Electrical & Electronics

### A force f is applied at the tip of the uniform bar element

A force F is applied at the tip of the uniform bar element shown in the figure. The initial length and the cross-sectional area of the bar are, respectively, A 0  and L 0 . The elastic modulus of the material is E. Calcu ...

### Does a large bolt-to-joint stiffness ratio increase or

Does a large bolt-to-joint stiffness ratio increase or decrease the possibility of fatigue failure of the bolt and why? Name at least three bolt, thread, or bolt and thread configurations which can improve the fatigue re ...

### 1 repeat the previous problem without the assumption that

1. Repeat the previous problem without the assumption that the velocity in the heating section is negligible. The ratio of the flow area of the heating section to the chimney flow area is R. 2. Consider a 4-cm pipe that ...

### Approximate by a number of terms of your choice through the

Approximate (by a number of terms of your choice) through the three forms of Fourier series expansion the periodic signal that in one period is given by Each time, a. Plot the approximate signal in time of three periods. ...

### In the system shown in figure 753 a passive nonlinear

In the system shown in Figure 7.53, a passive nonlinear element having the indicated volt-ampere characteristic is connected to an initially charged line at t = 0. Find the voltage across the nonlinear element immediatel ...

### 1 briefly outline the reasoning used for the removal of the

1. Briefly outline the reasoning used for the removal of the inconsistency with Maxwell's equations of the intuitively derived fields due to the Hertzian dipole. 2. Discuss the characteristics of the complete electromagn ...

### 1 if a communication is unicast how can we use rsvp which

1. If a communication is unicast, how can we use RSVP, which is designed for multicast in IntServ? 2. How can multicasting be achieved using DiffServ? 3. Why do we need Path and Resv messages in RSVP? 4. How many per-hop ...

### 1 implement the 2-to-4 decoder using 7404 not an 7808 and

1. Implement the 2-to-4 decoder using 7404 (NOT) an 7808 (AND) chips on your breadboard. 2. Implement the 2-to-4 decoder circuit with a 74139 chip on your breadboard. 3. Implement a 1-to-2 decoder in Logisim. Implement t ...

### A certain communication channel has a bandwidth of 10 khz a

A certain communication channel has a bandwidth of 10 kHz. A pulse of 0.5 ms duration is transmitted over this channel. a. Determine the width (duration) of the received pulse. b. Find the maximum rate at which these pul ...

### 1 why may researchers not offer potential participants

1. Why may researchers not offer potential participants large incentives (for example, a large amount of money) to participate in research? 2. In general, how much mental or physical risk is permissible in research? 3. D ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro