Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Physics Expert

Q1. The final tensile strength of a material was tested by using 10 samples.

The outcomes of the tests were as shown below:

711 N mm–2,  732 N mm–2, 759 N mm–2, 670 N mm–2, 701 N mm–2, 765 N mm–2, 743 N mm–2, 755 N mm–2, 715 N mm–2,  713 N mm–2.

a) Find out the mean and standard deviation of such results.

b) Express the values found in (a) in the GPa.

Q2. The component shown below is to be produced in the batches of 1000.

519_casting.jpg

a) State three main categorizations of castings by which the component could be produced.

b) Describe how each of these methods will influence the properties of the components produced (consider material and non-material properties ex: cost)

c) Name the methods which you have stated in (a) would you propose?

Give reasons to support your answer.

Physics, Academics

  • Category:- Physics
  • Reference No.:- M99882

Have any Question? 


Related Questions in Physics

An elite tour de france cycler can maintain an output power

An elite Tour de France cycler can maintain an output power of 450 W during a sustained climb. At this output power, how long would it take an 85 kg cycler (including the mass of the bike) to climb the 1100 meter high Al ...

What is the maximum voltage that can be generated by a

What is the maximum voltage that can be generated by a silicon solar cell?

The table gives the position of a particle moving along the

The table gives the position of a particle moving along the x-axis as a function of time in seconds, where x is in meters. What is the average velocity of the particle from t = 0 to t = 4?

The blood flow speed through an aorta with a radius of 1 cm

The blood flow speed through an aorta with a radius of 1 cm is 0.28 m/s. if hardening of the arteries causes the aorta to be constricted to a radius of 0.8 cm, what is the new blood flow speed?

If k ge 1 the graphs of y sin x and y ke-x intersect for

If k ≥ 1, the graphs of y = sin x and y = ke -x intersect for x ≥ 0. Find the smallest value of k for which the graphs are tangent. What are the coordinates of the point of tangency?

Draw to scale the three electron energy level and

Draw to scale the three electron energy level and transition energy diagrams of the isolated neutral He atom (with two electrons) and the He+ lon (with on electron) in analogy to Figure (a)-(c) but taking into account th ...

On may 9 2007 cbs evening news had a 43 point rating

On May 9, 2007, CBS Evening News had a 4.3 point rating. (Ratings measure the number of viewers.) News executives estimated that a 0.1 drop in the ratings for the CBS Evening News corresponds to a $5.5 million drop in re ...

Describe the relationship between electron orbital energy

Describe the relationship between electron orbital energy levels and the energy of light that electrons emit for atoms in a gas.

A proton is travelling at a speed of 4 x 105 ms moves into

A proton is travelling at a speed of 4 x 105 m/s moves into a series of charged parallel plates as shown below. a) What is the impact speed on the third plate? b) Why can you not use high-school kinematics to get the ans ...

A using a calculator or computer sketch the graph of y 2ex

(a) Using a calculator or computer, sketch the graph of y = 2ex + 5e-x for -3 ≤ x ≤ 3, 0 ≤ y ≤ 20. Observe that it looks like the graph of y = cosh x. Approximately where is its minimum? (b) Show algebraically that y = 2 ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen