+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1: If the vertical amplifier of the oscilloscope consists of a bandwidth of 15 MHZ, what is the fastest rise time that an input might have to be displayed devoid of distortion?

problem 2: Find out the velocity of the electron beam in an oscilloscope if the voltage applied to its accelerating anode is 2000V.

problem 3: The deflection sensitivity of cathode ray tube is 0.06mm/V and unknown voltage applied to the deflection plates shifts the spot by 4mm in the direction of left in the horizontal direction. Find out the unknown applied voltage.

problem 4: The X deflecting plates in a cathode ray tube are 15 mm long and 6mm apart. The center of the plates is 20 cm from the screen. The accelerating voltage is 2500 V. Find out the deflection sensitivity and deflection factor of the cathode ray tube.

problem 5: The lissajous pattern of oscilloscope is stationary and has 5 vertical maximum values and 4 horizontal maximum values. The frequency of horizontal input is 1200 Hz. What is the frequency of vertical input?

problem 6: The X deflecting plates in a cathode ray tube are 5mm apart and 25mm long. The center of plates is 20 cm from the screen. The accelerating voltage is 3000V. What is the rms value of the sinusoidal voltage applied to X deflecting plates if the length of the trace obtained on the screen id 10 cm. Determine as well the electrostatic deflection sensitivity of the above CRT?

problem 7: The deflection sensitivity of a CRT is 0.05mm/V and an unknown voltage applied to the horizontal Deflection plates shifts the spot by 5mm in the direction of right in the horizontal direction. Find out the unknown applied voltage.

problem 8: The X deflecting plates in a CRT are 20mm long and 5mm apart. The center of the plate is 0.25m from screen. The accelerating voltage is 3000V. What is the deflection sensitivity and deflection factor of the CRT?

Electrical & Electronics, Engineering

• Category:- Electrical & Electronics
• Reference No.:- M97606

Have any Question?

## Related Questions in Electrical & Electronics

### 1 find the unit vector normal to the plane then find the

1. Find the unit vector normal to the plane . Then find the distance from the origin to the plane. 2. Write the expression for the differential length vector dl at the point (1, 2, 8) on the straight line and having the ...

### A bandpass signal has bandwidth of 5 khz centered at fc 20

A bandpass signal has bandwidth of 5 kHz centered at fc = 20 kHz. Determine the permissible ranges of sampling frequency so that the original signal can be recovered from its samples. Redo the problem if the frequencies ...

### A communication link at a frequency of 30 mhz uses a

A communication link at a frequency of 30 MHz uses a half-wave dipole for the transmitting antenna and a small loop (directivity equal to 1.5) for the receiving antenna, involving a distance of 100 km. The antennas are o ...

### Solve problem using the secant method do not use the

Solve Problem using the secant method. Do not use the incremental force method. Discuss about the convergence rate. Problem :- Consider a uniform bar with a constant Young's modulus, E = 100 MPa; cross-sectional area, A ...

### Suppose that a continuous-time system is described by the

Suppose that a continuous-time system is described by the impulse response a. Compute the transfer function of the system. b. Find out if the system is BIBO stable. c. Plot the poles and the zeros of the system. d. Write ...

### Does the velocity distribution in example satisfy

Does the velocity distribution in Example satisfy continuity? Example A rotating shaft, as illustrated in Figure, causes the fluid to move in circular streamlines with a velocity that is inversely proportional to the dis ...

### In the system shown in figure 755 steady-state conditions

In the system shown in Figure 7.55, steady-state conditions are established with the switch S closed.At t = 0, he switch is opened. (a) Sketch the voltage and current along the system for t = 0-. (b) Find the total energ ...

### Can sell them for on a dollarper-square meter basis to make

can sell them for on a dollarper-square meter basis to make the resulting PV system no more expensive than when using a fixed mount system. Using simple dc, STC ratings along with the following assumptions, how much can ...

### Afirst-order ltic system has a characteristic root lambda

A first-order LTIC system has a characteristic root λ = -10 4 . a. Determine T r , the rise time of its unit step input response. b. Determine the bandwidth of this system. c. Determine the rate at which the information ...

### 1 assume alice needs to send an e-mail to bob explain how

1. Assume Alice needs to send an e-mail to Bob. Explain how the confidentiality of the e-mail is achieved using S/MIME. 2. When we talk about authentication in SSL, do we mean message authentication or entity authenticat ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro