Pulleys introduce a possible source of error because of, Ask an Expert

Academics

*Pulleys introduce a possible source of error because of their possible friction. Given that they are a source of error, why are the pulleys used at all?*To determine the force acting on each mass it was assumed that g=9.80m/sec2. The value of g at the place where the experiment is performed may be slightly different from that value. State what effect (if any) it would have on the percentage error calculated for the comparisons. To test your answer to the question, leave g as a symbol in the calculation of the percentafe error.

View complete question

Physics, Academics

Category:- Physics
Reference No.:- M91416728

Have any Question?Write your Review or question?

Related Questions in Physics

A clock is set against an accurate standard and 30 days

A clock is set against an accurate standard and 30 days later is found to be in error by 12 seconds. What is the percentage of error in its time keeping?

Question a sump pump is draining a flooded basement at the

Question: A sump pump is draining a flooded basement at the rate of 0.650 L/s, with an output pressure of 2.00 ? 10 5 N/m 2 . Neglect frictional losses in both parts of this problem. (a) The water enters a hose with a 3 ...

Question one of the most worrisome waste products of a

Question: One of the most worrisome waste products of a nuclear reactor is plutonium 239 ( 239 Pu). This nucleus is radioactive and decays by splitting into a helium-4 nucleus and a uranium-235 nucleus ( 4 He + 235 U), ...

Question a slide projector needs to create a 84 cm high

Question: A slide projector needs to create a 84 cm high image of a 2.0 cm tall slide. The screen is 240 cm from the slide. Assume that it is a thin lens. (a) What focal length does the lens need? cm (b) How far should y ...

The equation for motion for the ideal spring-mass system

The equation for motion for the ideal spring-mass system as derived in class is, ma+kx=0, where, m=mass, a=acceleration, k=spring stiffness, and x=displacement. 1) Describe briefly how the equation for motion arises from ...

In an attempt to skip a rock off the surface of a lake you

In an attempt to skip a rock off the surface of a lake, you throw the rock from a height h=1.67 m above the lake surface with an initial speed of v0 = 6.85 m/s at an angle of θ=12.3° below the horizontal. How long until ...

Question r 1097107 m-1a what is the wavelength of the line

Question: R= 1.097*10^7 m^-1 A) What is the wavelength of the line corresponding to n=4 in the Balmer series? B) What is the wavelength of the line corresponding to n=5 in the Balmer series? C) What is the smallest wavel ...

Question a research submarine has a 40-cm-diameter window

Question: A research submarine has a 40-cm-diameter window that is 8.1 cm thick. The manufacturer says the window can withstand forces up to 1.2 x 10 6 N. What is the submarine's maximum safe depth in salt water? The pre ...

Question a plastic rod is charged to -20 by rubbinga have

Question: A plastic rod is charged to -20 by rubbing. a. Have electrons been added to the rod or protons removed? Explain. b. How many electrons have been added or protons removed? The response must be typed, single spac ...

A 0900 kg hammer is moving horizontally at 950 ms when it

A 0.900 kg hammer is moving horizontally at 9.50 m/s when it strikes a nail and comes to rest after driving it 1.00 cm into a board. Calculate the duration of the impact. (s) What was the average force exerted on the nai ...

4,153,160 Questions Asked
13,132 Experts
2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Recent Questions

Ask Physics Expert