Plate steel is being coated with an anti-corrosion liquid, Ask an Expert

Academics

Plate steel is being coated with an anti-Corrosion liquid in a manufacturing process. The steel is 1.38m wide and is conveyed down the manufacturing line at 1.5m/s. The steel passes under nozzles that evenly and completely coat the steel. The desired application rate of anti-corrosion liquid is 0.010L/m^2. At what rate in L/min and gal/hr should the liquid be pumped to the nozzles.

View complete question

Physics, Academics

Category:- Physics
Reference No.:- M91709321

Have any Question?Write your Review or question?

Related Questions in Physics

Question a point charge of magnitude q is at the center of

question: A point charge of magnitude q is at the center of a cube with sides of length L. Part A: What is the electric flux ? through each of the six faces of the cube? Use 0 for the permittivity of free space. and Part ...

Question as shown in the figure there are 3 point charges

Question: As Shown in the figure, there are 3 point charges along the x-axis located at 3,8, and 11 cm. What is the x-component of the force on the charge located at x = 8 cm given that q = .85 uC in N? The response must ...

Question the nuclear mass of 141 ba is 140883 amu calculate

Question: The nuclear mass of 141 Ba is 140.883 amu. Calculate the Binding energy per nucleon for 141 Ba. In J/Nucleon. The response must be typed, single spaced, must be in times new roman font (size 12) and must follow ...

Question oppositely charged parallel plates are separated

Question: Oppositely charged parallel plates are separated by 5.31 mm. A potential difference of 600 V exists between the plates. (a) What is the magnitude of the electric field between the plates? N/C (b) What is the ma ...

Question pluto moves in a fairly elliptical orbit around

Question: Pluto moves in a fairly elliptical orbit around the sun. Pluto's speed at its closest approach of 4.43Ã-109km is 6.12 km/s. Part A: What is Pluto's speed at the most distant point in its orbit, where it is 7.30 ...

Question part a which of the following gives the correct

Question: Part A: Which of the following gives the correct permitted values of ml for l=2? Part B: A second important result is that electrons will fill the lowest energy states available. This would seem to indicate tha ...

An oil film n 148 floating on water n 133 is illuminated

An oil film (n = 1.48) floating on water (n = 1.33) is illuminated by white light at normal incidence. The film is 274 nm thick. The reflected light will be predominately a single color. Find the wavelength of the domina ...

A 00260 kg bullet moving horizontally at 400 ms embeds

A 0.0260 kg bullet moving horizontally at 400 m/s embeds itself into an initially stationary 0.500 kg block. What is their velocity just after the collision? The bullet-embedded block slides 8.0 m on a horizontal surface ...

A 0900 kg hammer is moving horizontally at 950 ms when it

A 0.900 kg hammer is moving horizontally at 9.50 m/s when it strikes a nail and comes to rest after driving it 1.00 cm into a board. Calculate the duration of the impact. (s) What was the average force exerted on the nai ...

Question part a what magnitude of force must the worker

Question: Part A: What magnitude of force must the worker apply to move the crate at constant velocity? Express your answer using two significant figures. Part B: How much work is done on the crate by this force when the ...

4,153,160 Questions Asked
13,132 Experts
2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Recent Questions

Ask Physics Expert