Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Physics Expert

Determining depth of the liquid in a tank by determining the surface level of liquid and pressure on the gage.

One means of determining surface level of liquid in a tank is by discharging a small amount of air through a small tube, the end of which is submerged in the tank, and reading the pressure on the gage that is tapped into the tube. Then the level of the liquid surface in the tank can be find outd. If the pressure on the gage is 20 kPa, what is the depth d of liquid in the tank?

1912_the liquid in a tank.jpg

Physics, Academics

  • Category:- Physics
  • Reference No.:- M917139

Have any Question? 


Related Questions in Physics

An 8- to 12-page paper should be well developed and convey

An 8- to 12-page paper, should be well developed and convey your understanding of the readings and concepts. It should also adequately answer the question. Your paper should be organized, coherent, and unified; it should ...

The input to a channel q is a word of 8 bits the output is

The input to a channel Q is a word of 8 bits. The output is also a word of 8 bits. Each time it is used, the channel flips exactly one of the transmitted bits, but the receiver does not know which one. The other seven bi ...

Si gaas and cds crystals are exposed to a yellow light of

Si, GaAs and CdS crystals are exposed to a yellow light of wavelength 5500A and intensity 10 12  photons/cm 2 -sec. Verify that the photon energy Is 2.25eV. How many electron-hole pairs are generated per unit volume per ...

A representative volume element dxdydz of a uniformly doped

A representative volume element dxdydz of a uniformly doped n-type silicon crystal contains 100 substitutional phosphorus donors distributed on the superlattice so there is no local fluctuation of positions. Which of the ...

In problems 99-100 show that the curves meet at least once

In Problems 99-100, Show that the curves meet at least once and determine whether the curves are perpendicular at the point of intersection.

A race car completes a lap on a 1600 m long track with an

A race car completes a lap on a 1600 m long track with an average speed of 250 km/h. If the car's average speed on the first half of the track was 205 km/h, what was its average speed on the second half?

A 162 g mass is hung on a spring as a result the spring

A 162 g mass is hung on a spring. As a result the spring stretches 19.5 cm. If the object is then pulled an additional 3.0 cm downward and released, what is the period of the resulting oscillation? Give your answer in se ...

Two ordinary dice are thrown repeatedly the outcome of each

Two ordinary dice are thrown repeatedly; the outcome of each throw is the sum of the two numbers. Joe Shark, who says that 6 and 8 are his lucky numbers, bets even money that a 6 will be thrown before the first 7 is thro ...

Starting from rest a runner reaches a speed of 27 ms in 20

Starting from rest, a runner reaches a speed of 2.7 m/s in 2.0 s. In the same 2.0 s time, a motorcycle increases speed from 38.0 to 43.0 m/s. In both cases, assume the acceleration is constant. (a) What is the accelerati ...

Since the 1950s the carbon dioxide concentration in the air

Since the 1950s, the carbon dioxide concentration in the air has been recorded at the Mauna Loa Observatory in Hawaii.4 A graph of this data is called the Keeling Curve, after Charles Keeling, who started recording the d ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro