Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Physics Expert

Unit conversions

Make the following unit conversions for parts (a) through (e) in table below. Show the work using a step-wise approach (e.g., show the conversions of the numerator and denominator separately).

Parameter

Convert From:

To:

Notes:

a. Velocity

Miles per hour (mph)

Meters per second (m/s)

 

b. Force

Pounds-force (lbf)

Newtons (N)

 

c. Pressure

Pounds-per-square inch (psi)

Kilopascals (kPa)        

1 Pa = 1 N/m2

d. Energy

Kilojoule (kJ)

Kilowatt-hour (kW-hr)

 

e. Viscosity

N-s/m2           

Centipoise (cP)           

1 cP = 0.01 gm/cm-s

 

Physics, Academics

  • Category:- Physics
  • Reference No.:- M917153

Have any Question? 


Related Questions in Physics

Sketch the posterior probability ppa saba f 3 what is the

Sketch the posterior probability P(pa | s=aba, F =3). What is the most probable value of pa (i.e., the value that maximizes the posterior probability density)? What is the mean value of pa under this distribution?

Air passes through a naphthalene tube that has an inside

Air passes through a naphthalene tube, that has an inside diameter of 2.5 cm, flowing at a bulk velocity of 15 m/s. The air is at 283 K and an average pressure of 1:013 × 10 5  Pa. Assuming that the change in pressure al ...

Find the capacity and optimal input distribution for the

Find the capacity and optimal input distribution for the three-input, three-output channel whose transition probabilities are:

I am just starting learning quantum physics and i am

I am just starting learning quantum physics , and I am starting from old quantum theories from black body radiation , but I am getting in trouble to understand Planck law derivation I am too confused about that derivatio ...

A uniform disc of radius r10 and mass m05 kg is attached to

A uniform disc of radius R=10 and mass M=0.5 kg is attached to the end of a uniform rigid rod of length L=1.0 m and mass m=0.5 kg. When the disc is suspended from a pivot as shown in fig, what will be the period of motio ...

Figure 350 shows the tangent line approximation to fx near

Figure 3.50 shows the tangent line approximation to f(x) near x = a. (a) Find a, f(a), f'(a). (b) Estimate f(2.1) and f(1.98). Are these under- or overestimates? Which estimate would you expect to be more accurate and wh ...

A mass on a spring vibrates in simple harmonic motion at a

A mass on a spring vibrates in simple harmonic motion at a frequency of 4.0 Hz and an amplitude of 4.0 cm. If a timer is started when its displacement is a maximum (hence x =4cm when t=0), what is the acceleration magnit ...

A remote controlled car has a momentum given by p 043

A remote controlled car has a momentum given by p = [(0.43 kg*m/s²) t²- (0.2 kg*m/s²) t ] î + (0.87 kg*m/s²) t j. What are the x- and y-components of the net force on the car.

A baseball hit at an angle of theta to the horizontal with

A baseball hit at an angle of θ to the horizontal with initial velocity v0 has horizontal range, R, given by Here g is the acceleration due to gravity. Sketch R as a function of θ for 0 ≤ θ ≤ π/2. What angle gives the ma ...

1 by how much could the size of a file be reduced given

1. By how much could the size of a file be reduced given that it is an ASCII file? How would you achieve this reduction? 2. What are the mathematical shapes of the curves between the cusps?

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro