Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: What is the main purpose of the error detector in the recorder?

problem 2: List all the typical frequency responses of the strip chart recorder.

problem 3: List all the three functions that a recorder might simultaneously serve in the industrial applications.

problem 4: List out minimum five applications which must be considered while choosing a recording instrument?

problem 5: If the frequency of a signal to be recorded with a strip chart recorder is 15 Hz, what chart speed should be employed to record one complete cycle on 5mm of recording paper?

problem 6: The chart speed of a recording instrument is 10 mm/sec. If the time base of the recorded signal is 20 mm, then determine the frequency of the recorded signal?

problem 7: Describe the functioning of a fundamental type of strip chart recorder. Describe the different types of marking method used in it.

problem 8: describe the working of a galvanometric type of strip chart recorder. What are the various types of tracing systems used in it? Describe with the help of appropriate diagram.

problem 9: Describe, with the help of diagram, the working of a null type recorder. Differentiate between single point and multi point recorders.

problem 10: What do you mean by X-Y recorder? How do you differentiate it from an X-t or Y-t recorder? Describe, the appropriate circuit diagram, the working of an X-Y recorder. describe its applications.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M97641

Have any Question? 


Related Questions in Electrical & Electronics

Power mosfet breakdown voltage 800v must conduct 10a when

power mosfet breakdown voltage 800v must conduct 10A when on with a maximum on state voltage 4v.If the current density in the mosfet must be limited to 200A/cm,estimate the conduxting area

1 what is the total distance around the circumference of a

1. What is the total distance around the circumference of a circle of radius 1 m? What is the total vector distance around the circle? 2. What is the total surface area of a cube of sides 1 m? Assuming the normals to the ...

The rate of shear work per unit volume is given by the

The rate of shear work per unit volume is given by the product tv. For a parabolic velocity profile in a circular tube (see given Example), determine the distance from the wall at which the shear work is maximum. Example ...

1 in logisim implement an 8-to-1 mux using 2 4-to-1 muxes

1. In Logisim implement an 8-to-1 MUX using 2 4-to-1 MUXes and a 2-to-1 MUX. 2. In Logisim implement an 8-to-1 MUX using 4 2-to-1 MUXes and a 4-to-1 MUX. 3. In Logisim implement a circuit similar to the one in figure 8-1 ...

1 find two differential length vectors tangential to the

1. Find two differential length vectors tangential to the surface at the point (2, 4, 1) and then find a unit vector normal to the surface at that point. 2. A hemispherical bowl of radius 2 m lies with its base on the xy ...

1 why is it that the distances r1 and r2 in the phase

1. Why is it that the distances r 1 and r 2 in the phase factors in equations (8.47a) and (8.47b) cannot be set equal to r, but the same quantities in the amplitude factors can be set equal to r? 2. What is an array fact ...

1 fluid flows between two parallel plates a distance h

1. Fluid flows between two parallel plates, a distance h apart. The upper plate moves at velocity, v 0 ; the lower plate is stationary. For what value of pressure gradient will the shear stress at the lower wall be zero? ...

An exhaust stream leaving a semiconductor fabrication plant

An exhaust stream leaving a semiconductor fabrication plant contains 4 mol % volatile organic chemical, VOC, pollutant. Twenty-five cubic meters per minute enter the bottom of a packed absorption tower and flows counterc ...

Suppose that a discrete-time system is specified by the

Suppose that a discrete-time system is specified by the transfer function Compute and plot a. The step response of the system b. The impulse response of the system c. The response of the system to the input signal

Consider a plane-strain square element with unit depth as

Consider a plane-strain square element with unit depth as shown in the figure. Use the St. Venant-Kirchhoff isotropic material model with two Lame's constants λ and μ. A uniformly distributed force T x  (force per area) ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro