Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Physics Expert

Determination of work completed in pushing the block against the wall to overcome friction.

A 2.60 block is pushed 1.69 m up a vertical wall with a constant speed with a constant force of magnitude F applied at angle 55.4 degrees with the horizontal. g= 9.8 m/s2. If the coefficient of kinetic friction between block and wall is 0.54, find out the work completed by the F and express in J.

Physics, Academics

  • Category:- Physics
  • Reference No.:- M917467

Have any Question? 


Related Questions in Physics

As a spacecraft approaches a planet the rocket engines on

As a spacecraft approaches a planet, the rocket engines on it are fired (turned on) to slow it down so it will go into orbit around the planet. The spacecraft's mass is 2,525 kg and the thrust (force) of the rocket engin ...

Linear binary codes use the input symbols 0 and 1 with

Linear binary codes use the input symbols 0 and 1 with equal probability, implicitly treating the channel as a symmetric channel. Investigate how much loss in communication rate is caused by this assumption, if in fact t ...

The graphs of sin x and cos x intersect once between 0 and

The graphs of sin x and cos x intersect once between 0 and π/2. What is the angle between the two curves at the point where they intersect? (You need to think about how the angle between two curves should be defined.)

Determine the value of henrys law constant in pakgm3 of

Determine the value of Henry's law constant, in Pa/(kg/m 3 ) of chlorine for the chlorine-water system. The following equilibrium data at 293 K were reported in the Chemical Engineering Handbook.

A certain sound has an intensity of A certain sound has an intensity of 9.195275×10 -4

A certain sound has an intensity of 9.195275×10 -4  W/m 2  2.33 m from its source. What is the power emitted by this source in watts? Express your result to three significant digits and in scientific notation. Hint: The ...

A camera is equipped with a lens with a focal length of 36

A camera is equipped with a lens with a focal length of 36 cm. When an object 2.9 m (290 cm) away is being photographed, what is the magnification?

If a circuit requires a capacitor to give good coupling at

If a circuit requires a capacitor to give good coupling at 200Hz and the resistance the capacitor is connected to is 3Kohms, what value capacitor is needed?

In problems 99-100 show that the curves meet at least once

In Problems 99-100, Show that the curves meet at least once and determine whether the curves are perpendicular at the point of intersection.

Each of the bodies shown is homogeneous and has a mass of

Each of the bodies shown is homogeneous and has a mass of 30 kg. Assume friction at all contact surfaces. Draw the fully dimensioned FBD for each body and determine the number of unknowns.

A particle moves at varying velocity along a line and s ft

A particle moves at varying velocity along a line and s = f(t) represents the particle's distance from a point as a function of time, t. Sketch a possible graph for f if the average velocity of the particle between t = 2 ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro