Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: Design and describe 4- line to 16 line decoder with 74138.

problem 2:

a) Design 4:1 Mux with logic diagram and symbolic representation.

b) Convert the binary numbers to gray codes using Ex-OR gates

• 1001
• 11001111
• 10000001
• 10011

problem 3:

a) Draw the logic diagram of 74x283 IC and describe the operation?

b) prepare brief notes on BCD to binary converter?

problem 4:

a) Design a 3 input 5 output multiplexer? prepare the truth table and draw the logic diagram.

b) prepare brief notes on full subtractor.

problem 5:

a) Give the logic diagram of 74x147 and describe its truth table?

b) prepare brief notes on half subtractor?

problem 6:

a) Design a 2-bit comparator by using logic gates and draw its logic diagram.

b) Describe BCD to 7-segment decoder with the help of a truth table.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M93623
  • Price:- $70

Priced at Now at $70, Verified Solution

Have any Question? 


Related Questions in Electrical & Electronics

Calculate the approximate diameter and length of stator

Calculate the approximate diameter and length of stator core, the number of stator slots and the number of conductors for a 20KW,400V,3 phase,4pole,1200rpm,delta connected induction motor. Bav=0.5T, Kw=0.82, ac=26000amp. ...

1 energy calculationsbuilding sf 20000 sfelectric rateuse

1. Energy Calculations Building SF = 20,000 sf Electric Rate: Use MTSU Utility Rate Schedule - Seasonal Rates Lighting: 2 watts/sf hours of operation = 19 hours per day Motors: One water pump motor, 80% efficient, runnin ...

Determine the maximum film velocity in problemproblem

Determine the maximum film velocity in Problem. Problem Aviscous film drains uniformly down the side of a vertical rod of radius R. At some distance down the rod, the film approaches a terminal or fully developed flow su ...

1 if the plate shown is inclined at an angle as shown what

1. If the plate shown is inclined at an angle as shown, what are the forces F x  and F y  necessary to maintain its position? The flow is frictionless. 2. A steady, incompressible, frictionless, two-dimensional jet of fl ...

A force f is applied at the tip of the uniform bar element

A force F is applied at the tip of the uniform bar element shown in the figure. The initial length and the cross-sectional area of the bar are, respectively, A 0  and L 0 . The elastic modulus of the material is E. Calcu ...

1 what is snells law2 what is meant by the plane of

1. What is Snell's law? 2. What is meant by the plane of incidence? Distinguish between the two different linear polarizations pertinent to the derivation of the reflection and transmission coefficients for oblique incid ...

1 consider three equally spaced sources of strength m

1. Consider three equally spaced sources of strength m placed at (x, y) = ( a, 0),(0, 0), and (a, 0). Sketch the resulting streamline pattern. Are there any stagnation points? 2. Sketch the streamlines and potential line ...

An estimate is needed on the lift provided by a hydrofoil

An estimate is needed on the lift provided by a hydrofoil wing section when it moves through water at 60 mph. Test data are available for this purpose from experiments in a pressurized wind tunnel with an airfoil section ...

A determine the magnitude of the x and y components of the

(a) Determine the magnitude of the x and y components of the force exerted on the fixed blade shown by a 3-ft 3  /s jet of water flowing at 25 fps. (b) If the blade is moving to the right at 15 fps, find the magnitude an ...

Consider the simple rc circuit shown in fig p23-3 let r 1

Consider the simple RC circuit shown in Fig. P2.3-3. Let R = 1 kΩ and C = 1 nF. (a) Find the system transfer function. (b) Plot the magnitude and phase responses. (c) Show that a lowpass signal x(t) with bandwidth W « 10 ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro