Compute the critical edge load n cr x for a plate simply, Ask an Expert

Academics

Compute the critical edge load N CR x for a plate simply supported around the boundary, with length a = 2 m (along x), width b = 1 m, t = 1 cm.

The laminate is made of E-glass-polyester with V_f = 0.5 with a symmetric configuration defined by α = β = 0.2, γ = 0.6. Compare your answer with given Figure.

341_Fig 6.jpg

View complete question

Physics, Academics

Category:- Physics
Reference No.:- M92168544

Have any Question?Write your Review or question?

Related Questions in Physics

Question suppose the free-fall acceleration at some

Question: Suppose the free-fall acceleration at some location on earth was exactly 9.8000 m/s^2. What would it be at the top of a 1000 -tall tower at this location? The response must be typed, single spaced, must be in t ...

If you pick up a 57 kg object from the ground and lift

If you pick up a 5.7 kg object from the ground and lift it to a height of 0.98 m above the ground in 1.66 seconds, how much power is expended? (Use the value of 9.8 m/s 2 for the acceleration of gravity.) Please provide ...

Question in short-track speed skating the track has

Question: In short-track speed skating, the track has straight sections and semicircles 16 m in diameter. Assume that a 64kg \;kg skater goes around the turn at a constant 11m/s Part A: What is the horizontal force on th ...

A 0900 kg hammer is moving horizontally at 950 ms when it

A 0.900 kg hammer is moving horizontally at 9.50 m/s when it strikes a nail and comes to rest after driving it 1.00 cm into a board. Calculate the duration of the impact. (s) What was the average force exerted on the nai ...

Question a proton has been accelerated from rest through a

Question: A proton has been accelerated from rest through a potential difference of -1350 V. What is the proton's kinetic energy, in electron volts? What is the proton's kinetic energy, in joules? What is the proton's sp ...

Question a steel cable with mass is lifting a girder the

Question: A steel cable with mass is lifting a girder. The girder is speeding up. Part A Draw a free-body diagram for the steel cable. Draw the vectors starting at the black dots. The location and orientation of the vect ...

A ball rolls off a table with a horizontal velocity of 5 ms

A ball rolls off a table with a horizontal velocity of 5 m/s if takes 0.6 seconds for it to reach the floor a) what's the vertical component of the ball's velocity just before it hits the floor b) what's the horizontal c ...

Question suppose that the coefficient of kinetic friction

Question: Suppose that the coefficient of kinetic friction between Zak's feet and the floor, while wearing socks, is 0.250. Knowing this, Zak decides to get a running start and then slide across the floor. If Zak's speed ...

A puck is moving on an air hockey table relative to an x y

A puck is moving on an air hockey table. Relative to an x, y coordinate system at time t = 0 s, the x components of the puck's initial velocity and acceleration are v0x = +7.8 m/s and ax = +5.3 m/s2. The y components of ...

Question a ring with radius r and a uniformly distributed

Question: A ring with radius R and a uniformly distributed total charge Q lies in the xy plane, centered at the origin. Part A: What is the potential V(z) due to the ring on the z axis as a function of z? Express your an ...

4,153,160 Questions Asked
13,132 Experts
2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Recent Questions

Ask Physics Expert