Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Physics Expert

Find the magnitude and the direction of the resultant force and coefficient of kinetic friction.

1. An object is pulled northward by the force of 10 N and at the same time another force of N pulls it southward. What is the magnitude and direction of the resultant force on object?

2. An object slides on the level surface in the +x direction. It shows and comes to a stop with a constant acceleration of -2.45m/s2. What is the coefficient of kinetic friction between the object and the floor?

Physics, Academics

  • Category:- Physics
  • Reference No.:- M917026

Have any Question? 


Related Questions in Physics

Ammonia nh3 in air is being absorbed into water within the

Ammonia, NH 3 , in air is being absorbed into water within the enclosed tank shown in the figure below. The liquid and gas phases are both well mixed, and mass transfer occurs only at the exposed gas-liquid interface. Th ...

Many texts draw figure 81 in the form of a venn diagram

Many texts draw figure 8.1 in the form of a Venn diagram (figure 8.2). Discuss why this diagram is a misleading representation of entropies. Hint: consider the three-variable ensemble XY Z in which x ∈ {0, 1} and y ∈ {0, ...

Bullets of mass22g are fired in parallel paths with speeds

Bullets of mass2.2g are fired in parallel paths with speeds of216m/s through a hole2.0mm in diameter. How far from the hole must you be to detect a1.4cm diameter spread in the beam of bullets?

An lr combination is connected to an ideal battery if l 10

An LR combination is connected to an ideal battery. If L= 10 mH, R = 2.0 ohms and E = 2.0 v how much time will it take for the current to reach 0.63 A?

A particular airplane will reach liftoff at a speed of 120

A particular airplane will reach liftoff at a speed of 120 km/h. (a) What minimum constant acceleration does the airplane require for it to liftoff after a takeoff run of 280 m? (Enter the magnitude only.) (b) How long d ...

The graphs of sin x and cos x intersect once between 0 and

The graphs of sin x and cos x intersect once between 0 and π/2. What is the angle between the two curves at the point where they intersect? (You need to think about how the angle between two curves should be defined.)

On a certain day the barometric pressure at sea level is

On a certain day the barometric pressure at sea level is 30.1 in. Hg, and the temperature is 708F. The pressure gage in an airplane in flight indicates a pressure of 10.6 psia, and the temperature gage shows the air temp ...

Hypochlorite ion used as the chlorinating agent in swimming

Hypochlorite ion, used as the chlorinating agent in swimming pools, can decompose exothermically, in rare occasions even causing ires. he principal decomposition mechanism is believed to be a. Find the steady-state conce ...

1 why are the valence electrons the most important on

1. Why are the valence electrons the most important on influencing the electrical properties of silicon? Why are the core electrons not as important? Why are the core electrons important to distinguish Si, Gs, GaAs and o ...

Starting from rest a runner at a track meet reaches a speed

Starting from rest, a runner at a track meet reaches a speed of 9.6 m/s in 1.5 s. How far does she run during this time, assuming her acceleration is uniform?

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro