Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Physics Expert

Calculating the potential of an upper plate of a parallel plate capacitor while the electron stops just before reaching the plate.

An electron is shot upward directly perpendicular to the lower plate of a parallel plate capacitor. Its initial velocity is 3.0 x 104 m/s. What must be the potential of the upper plate if the electron stops just before reaching it? The lower plate is at a potential of 0 V. How does this answer change if the electron is shot at an angle of 45° to the plate?

Physics, Academics

  • Category:- Physics
  • Reference No.:- M917233

Have any Question? 


Related Questions in Physics

Below is the calculator result for the operation indicated

Below is the calculator result for the operation indicated. Enter the answer to the correct number of significant figures for this calculation, using the rules for significant figures. 3.82193 + 10.5861 = 14.40803

Prove that detailed balance implies invariance of the

Prove that detailed balance implies invariance of the distribution P(x) under the Markov chain T. Proving that detailed balance holds is often a key step when proving that a Markov chain Monte Carlo simulation will conve ...

An object located 323 cm in front of a lens forms an image

An object located 32.3 cm in front of a lens forms an image on a screen 9.69 cm behind the lens. Find the focal length of the lens. Answer in units of cm. 010 (part 2 of 2) 10.0 points What is the magni?cation of the obj ...

Newtons second law of motionpurpose - to determine the

Newton's Second Law of Motion Purpose - To determine the relationship between net force, mass, and acceleration and to use vector addition to determine the net force on an object. Discussion 1. In the situation with a co ...

A pinball machine uses a spring launcher that is compressed

A pinball machine uses a spring launcher that is compressed 6.6 cm to launch a ball up a 17 °ramp. Assume that the pinball is a solid uniform sphere of radius r = 1.0cm and mass m = 28 g .If it is rolling without slippin ...

A juniper-wood plank measuringnbsp032nbspft by 1 ft

A juniper-wood plank measuring 0.32 ft by 1 ft by 12 ft is totally submerged in water. (a) What is its weight? (b) What is the buoyant force acting on it? (c) What is the size and the direction of the net force on it?

1 using only basic physics no algebra and no equations show

1. Using only basic physics, no algebra, and no equations, show that at T=OK, E F =(E C -E D )/2 in an n-type semiconductor with N DD  = 10 and N AA  = 0. 2. Using only basic physics, no algebra, and no equations, show t ...

How to measure a classifiers quality youve just written a

How to measure a classifier's quality. You've just written a new classification algorithm and want to measure how well it performs on a test set, and compare it with other classifiers. What performance measure should you ...

Consider the device shown below that will be used to

Consider the device shown below that will be used to humidity an air stream. In the current process, air containing 1.0 mol% water vapor (species A) at 40°C and 1.0 atm enters the tube of 3.0 cm inner diameter at a veloc ...

Suppose that one weekend day a hiker exerts 200 watts of

Suppose that one weekend day a hiker exerts 200 Watts of power while ascending 300 meters on a steep trail without a pack. The hiker repeats this trip the following weekend but is carrying an additional 10 kilograms in a ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen