A student added 500 ml of cold water to 50 ml of heated, Ask an Expert

Academics

A student added 50.0 mL of cold water to 50 mL of heated, distilled water in a styrofoam cup. The initial temperature of the cold water was 21.00 C and of the hot water, 21.95 C. The maximum temperature of the mix was found to be 24.81. Assume the density of water is 1.00 g mL and the specific heat is 4.184J g K. Determine the change in temperature for the Hot water. Determine the change in time for the cold water.

View complete question

Chemistry, Academics

Category:- Chemistry
Reference No.:- M91075671

Have any Question?Write your Review or question?

Related Questions in Chemistry

A power plant converts the heat energy in coal to

A power plant converts the heat energy in coal to electricity with 35% efficiency. Transmission losses are 10%. A factory then uses that electricity to make hydrogen with 50% efficiency, which is used in a fuel cell to m ...

What was the initial energy level of an electron if it was

What was the initial energy level of an electron if it was excited by a photon of wavelength 38.9µm and jumped to an energy level of 10?

A student weighed out 174 grams of sodium hydroxide pellets

A student weighed out 1.74 grams of sodium hydroxide pellets and added them to 48.0 grams of water in a calorimeter. Extrapolating back to the time of mixing yielded a temperature change at the time of mixing equal to 9. ...

2kmno4s rarr k2mno4s mno2s o2gif 250 l of o2g is needed

2KMnO 4 (s) → K 2 MnO 4 (s) + MnO 2 (s) + O 2 (g) If 2.50 L of O 2 (g) is needed at 1.00 atm and 20°C, what mass of KMnO 4 (s) should be decomposed? Assume the decomposition of KMnO 4 (s) goes to completion.

A paint contains 1800 ppm lead approximately what mass of

A paint contains 180.0 ppm lead. Approximately what mass of lead will be in 1.00 cm ^3 of this paint when 1.00 gal is uniformly applied to 445.0 ft 2 of a wall. The density of the paint is 8.00 lb/gal.

Suppose a tank is filled with a2g so that initial pressure

Suppose a tank is filled with A2(g) so that initial pressure is 0.8688 atm at temperature of 298K. Some of the A2(g) dissociates and when the system reaches equlibrium the total pressure in the tank is 1.275 atm. Calcula ...

What volume of 0600 m hcl is required to react completely

What volume of 0.600 M HCl is required to react completely with 2.50 g of sodium hydrogen carbonate? NaHCO3(aq) + HCl(aq) ? NaCl(aq) + CO2(g) + H2 O(l)

If 0050 mol hydrochloric acid hcl is mixed with 0050 mol of

If 0.050 mol hydrochloric acid (HCl) is mixed with 0.050 mol of sodium hydroxide (NaOH) in a "coffee cup" calorimeter, calculate the temperature change of 34.6 g of the resulting solution if the specific heat of the solu ...

Q1 in your gravimatric analysis experiment you weigh the

Q1: In your gravimatric analysis experiment, you weigh the precipitate of AgCl in a filtering crucible. You have to weight your filtering crucible first (three weighing measurement), then do the filtration. After drying ...

2 h2sg 3 o2g rarr 2 h2og 2 so2gusing standard enthalpies

2 H2S(g) + 3 O2(g) → 2 H2O(g) + 2 SO2(g) Using standard enthalpies of formation, calculate the standard enthalpy change for this reaction.

4,153,160 Questions Asked
13,132 Experts
2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Recent Questions

Ask Chemistry Expert