A 600 n force is applied at an angle of 35 degrees to a 700, Ask an Expert

Academics

a 60.0 n force is applied at an angle of 35 degrees to a 7.00 kg block pressed against a rough vertical wall and the block slides down the wall at constant velocity.

A. What is the coeffiant of kinetic friction between the block and the wall?

B. What is the normal force as a function of F? We are looking for the unknown applied force, Using Newton's second law of motion.

C. What is the kinetic friction force as a function of F?

D. What is the coeffiant of kinetic friction in the vertical direction?

View complete question

Physics, Academics

Category:- Physics
Reference No.:- M9875925

Have any Question?Write your Review or question?

Related Questions in Physics

Question the radius of our sun is 696 x 108 m and its total

Question: The radius of our Sun is 6.96 x 10 8 m, and its total power output is 3.85 x 10 26 W. (a) Assuming the Sun's surface emits as a black body, calculate its surface temperature. K (b) Using the result of part (a), ...

Question for this problem take the distance from the earth

Question: For this problem, take the distance from the Earth to the Sun to be 1.5 x 10 11 m and the radius of the Earth to be 6.38 x 06m. A) Using the fact that the earth orbits the Sun once per year, calculate the Earth ...

Question a textbook of mass 198kg rests on a frictionless

Question: A textbook of mass 1.98kg rests on a frictionless, horizontal surface. A cord attached to the book passes over a pulley whose diameter is 0.160m , to a hanging book with mass 3.01kg . The system is released fro ...

Question during your summer internship for an aerospace

Question: During your summer internship for an aerospace company, you are asked to design a small research rocket. The rocket is to be launched from rest from the earth's surface and is to reach a maximum height of 940m ...

Question in an old-fashioned amusement park ride passengers

Question: In an old-fashioned amusement park ride, passengers stand inside a3.0-m-tall, 5.0-m-diameter hollow steel cylinder with their backsagainst the wall. The cylinder begins to rotate about a verticalaxis. Then the ...

Question a parallel-plate air capacitor has a capacitance

Question: A parallel-plate air capacitor has a capacitance of 920 pF. The charge on each plate is 2.55 ?C What is the potential difference between the plates? If the charge is kept constant, what will be the potential di ...

Question suppose the emf generated by a coil rotating in a

Question: Suppose the emf generated by a coil rotating in a magnetic field is zero at t=0 and increases to its first peak at to=0.11 ms. When is the emf first one-fourth of its maximum, in seconds? When is the emf next o ...

Suppose the convention were adopted that defines w and w 0

Suppose the convention were adopted that defines W and W 0 in the first law of thermodynamics to be the "work done on the system by the surroundings." a. Write the first law with this alternate convention. b. Why do the ...

A ball with a mass of 15 kg is observed to move with an

A ball with a mass of 1.5 kg is observed to move with an acceleration of 6 m/s2. What is the size of the net force acting on the ball? A 2.5-kg block being pulled across a table by a horizontal force of 80 N also experie ...

Suppose that your users manual lists your cars weight at

Suppose that your user's manual lists your car's weight at 2800 pounds, and you calculate a weight of 2900 pounds based on measurements of the car's tire areas and pressure. What is the percent error between your experim ...

4,153,160 Questions Asked
13,132 Experts
2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Recent Questions

Ask Physics Expert