Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

1) prepare the flowchart and program to perform the following: A pressure sensor in a cooling system measures pressure of the refrigerant and is connected to Port -1 of the 8051. If pressure is greater than 200D, the controller is to set a high signal on Port-O, line-O; otherwise it is to be low. If the pressure is less than 45D then a high signal is to be sent on Port-O, line-1; otherwise it is to be low.

2) prepare the flowchart and program to output the triangle wave by counting from OOH to FFH and then back down to OOH again and repeating this pattern and outputting this to Port-I which has a DAC connected to it. Suppose no delay is to be added between outputting of the numbers.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M91911

Have any Question? 


Related Questions in Other Engineering

Time managementdiscuss some of the reasons why individuals

Time Management Discuss some of the reasons why individuals routinely over-estimate the time for project activities. How is this behavior detrimental to the schedule and project? Are some of these reasons more prevalent ...

Create the single line diagram of a substation having the

Create the single line diagram of a substation having the following equipments using a drawing software. You can use any drawing software available (e.g. Smartdraw, MS Visio, Microstation, AUTOCAD, Edraw etc.). -Incoming ...

Risk factors and gantt chartsquestion 1 project risk

Risk Factors and Gantt Charts Question 1: Project Risk factors • List the major risk factors for your project and the possible ways to mitigate this risks for your project. Question 2: Resource Evaluation • Produce and c ...

Assignment statementclimate change is a serious challenge

ASSIGNMENT STATEMENT Climate change is a serious challenge to the Kingdom of Saudi Arabia, which is under tremendous pressure as a result of the hyper aridity of the climate, severe shortage in water resources, rapidly g ...

1given the following transfer function modelsy1su1s g11s

1. Given the following transfer function models: y 1 (s)/u 1 (s) = g 11 (s) = 2/(s+3) y 1 (s)/u 2 (s) = g 12 (s) = -1/(s+1) y 2 (s)/u 1 (s) = g 21 (s) = -1/(s+7) y 2 (s)/u 2 (s) = g 22 (s) = 0.5/(s+4) a) Draw the 2x2 ope ...

Discussion-please share with your classmates an experience

Discussion- Please share with your classmates an experience where you have dealt with lack of accommodation for the user in the design of equipment, process, or product. What was done to accommodate the user? Which anthr ...

1 purposethe primary purpose of this project is to help you

1. Purpose The primary purpose of this project is to help you understand the pipelining process for a simple set of MIPS instructions. You will gain experience with basic pipelining principles, as well as the hazard cont ...

1 for a 77t truck with gross vehicle weight gvw of 136078

1. For a 77t truck with Gross Vehicle Weight (GVW) of 136078 kg with dual rear tyres and a tyre inflation pressure is 120 psi (or 8.43 kg/cm 2 ). Use the equivalent single tyre loading. i. Determine the contact surface a ...

Assignmentwhy program design is importantanswer the

Assignment Why Program Design is Important? Answer the following questions: 1. What is a program design? 2. Why program design is important? 3. What program design tools are available? Discuss in details by studying at l ...

Assignment air traffic control systemconsider the following

Assignment: Air Traffic Control System Consider the following goal model fragment for an air traffic control system shown below. The parent goal roughly states that aircraft routes should be sufficiently separated. The r ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen