Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

Answer the following problems.

problem 1) prepare in detail the significance of micropaleontology in Geological applications.

problem 2) Describe the term Paleoecology. Enumerate your answer giving criteria to establish the Paleoecology of foraminifera add a note on its significance.

problem 3) Describe the term Stratigraphy. Enumerate your answer with special reference to the stratigraphic classifications using rock units, time-rock units and magnetic elements an criteria.

problem 4) describe the Eocene Stratigraphy and Micropaleontology of the Sedimentary sequence of K.G. Basin. Add a note on the Paleoenvironmental setting of the basin due Eocene.

problem 5) prepare on the role of Organic Maturation in Hydrocarbon exploration.

problem 6) describe the following:

i) Correlation.

ii) Platform type basins.

iii) Characterisation of Tertiary Hydrocarbons.

problem 7) Attempt the following problems:

i) Types of Microfossils.

ii) Ecology of Ostracods.

iii) Species Diversity.

problem 8) Attempt the following problems:

i) Sequence stratigraphy.

ii) Stratigraphic procedures.

iii) Geological time scale.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M95320

Have any Question? 


Related Questions in Other Engineering

Problem 1a router is used to cut locating notches on a

Problem 1 A router is used to cut locating notches on a printer circuit board. The vibration level at the surface of the board as it is cut, is considered to be a major source of dimensional variation (lower the better) ...

Electronics i and labbridge rectifierintroductionthe lab is

Electronics I and Lab Bridge Rectifier Introduction: The lab is based on the previous lab from week 2 on half-wave and full-wave rectifiers and taking that knowledge to build a bridge rectifier. Materials and Equipment: ...

Labintroductionweek 2 lab is based on half-wave and

Lab: Introduction: Week 2 lab is based on half-wave and full-wave rectifiers. Rectifiers are widely used in power supplies to provide the required DC voltage. Please review the following videos before getting started wit ...

Problem 1nbspnbspnbspa letnbsphand calculate ab a-b ab ba

Problem 1:    (a) Let  Hand calculate A+B, A-B, AB, BA, CA, CB, and AC T . (b) Use MATLAB to verify your calculations. Problem 2: (a) Let Hand calculate |A|, r A , and A -1 if it exists. (b) Hand calculates the eigenvalu ...

Create the single line diagram of a substation having the

Create the single line diagram of a substation having the following equipments using a drawing software. You can use any drawing software available (e.g. Smartdraw, MS Visio, Microstation, AUTOCAD, Edraw etc.). -Incoming ...

Part -1chapter 1 - introduction introduce the project

Part -1: CHAPTER 1 - Introduction: Introduce the project problem; define the scope, aim and objectives of the investigations. CHAPTER 2 - Literature Review: Describe the literature/ theory reviewed which are relevant to ...

Time managementdiscuss some of the reasons why individuals

Time Management Discuss some of the reasons why individuals routinely over-estimate the time for project activities. How is this behavior detrimental to the schedule and project? Are some of these reasons more prevalent ...

Finite element analysis in engineering term assignmentfor

Finite Element Analysis in Engineering Term Assignment For the truss system above, do the following. Q1: (a) Solve for the x,y components of displacement of each joint using one bar element for each link. Show all work i ...

Discussion-please share with your classmates an experience

Discussion- Please share with your classmates an experience where you have dealt with lack of accommodation for the user in the design of equipment, process, or product. What was done to accommodate the user? Which anthr ...

1 summarise the steps in the development of an open pit

1. Summarise the steps in the development of an open pit mine. 2. Define or describe the following terms a. Bench height b. Working bench c. Crest d. Cut e. Toe f. Safety bench/catch bench g. Bench face angle h. Back bre ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro