Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

problem 1:

prepare down a critical note on the dissimilar techniques accessible for eliminating dross throughout melting of Aluminium alloys.

problem 2:

prepare down the ideal theoretical shape of the riser. Illustrate your answer in detail with the appropriate sketch.

problem 3:

What factors resolve riser adequacy? What factors determine riser economy?

problem 4:

Illustrate various welding procedures which can be employed for repair of castings.

problem 5:

Provide instances of the typical products of following processes: Precision casting, Die casting, Shell moulding.

problem 6:

prepare down the merits and demerits of carbon di-oxide moulding.

problem 7:

What causes surface shrinkage at the internal angles in the castings? How it can be eradicated?

problem 8:

What do you understand by the term inter dendritic shrinkage and why does it take place?

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M911071

Have any Question? 


Related Questions in Other Engineering

Stting up a xilinx project for the bcd clockobjective

Setting up a Xilinx project for the BCD Clock Objective: This document is intended to be used as a reference guide to aid in setting up and working with a Xilinx ISE WebPACK project for use with the BCD clock project. Pr ...

1the emf of a generator of 377 ohm internal impedance is a

1. The EMF of a generator of 377 ohm internal impedance is a 2 ps long pulse of 12 volt amplitude. The generator drives a 10km long section of transmission line of 377 ohm characteristic impedance and 3 x 10 8 m/s propag ...

Electronics lab transistor biasingintroductionlab is based

Electronics Lab: Transistor Biasing Introduction: Lab is based on the fundamentals of a transistor biasing and the analysis of the circuit. The goal of Transistor Biasing is to establish a known Q-point in order for the ...

1 for a 77t truck with gross vehicle weight gvw of 136078

1. For a 77t truck with Gross Vehicle Weight (GVW) of 136078 kg with dual rear tyres and a tyre inflation pressure is 120 psi (or 8.43 kg/cm 2 ). Use the equivalent single tyre loading. i. Determine the contact surface a ...

1 purposethe primary purpose of this project is to help you

1. Purpose The primary purpose of this project is to help you understand the pipelining process for a simple set of MIPS instructions. You will gain experience with basic pipelining principles, as well as the hazard cont ...

Microprocessorsmodule-simple automation systemsoverviewin

MICROPROCESSORS Module-Simple Automation Systems OVERVIEW In the final module, we cut the umbilical cord and try standalone operations of UNO board. You will learn about the applications of the AVR in various areas. We a ...

Smart home patient monitoring system abstractthe increasing

Smart Home Patient Monitoring System Abstract The increasing number elder people and illnesses that require continuous monitoring, along with the demand on hospital rooms and shortage of medical support, home monitoring ...

Assignmentpart 1bullop-amp introduction1read chapters 1-2

Assignment Part 1 • Op-Amp Introduction 1. Read Chapters 1-2 in the text Op Amps for Everyone Fourth Edition 2. For the configuration below: 3. o With Vin = 4Vrms, f = 1kHz answer the following for each case: o Calculate ...

Exercise 1charity is a big business in the united states

Exercise 1 Charity is a big business in the United States. The Web site charitynavigator.com gives information on roughly 5500 charitable organizations, and there are many smaller charities that fly below the navigator's ...

C project reportsi have two c program i need one reports

C++ Project Reports I have two C++ program i need one reports for ech one of the and i wnat them to be tn the same format in the instruction if there some the thing not right i will not accept it. The two must be diferen ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro