Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

Answer the following problems.

problem 1)a) With the help of appropriate diagram, describe horizontal axis wind turbine with two blades and list out the advantages and disadvantages of the same.

b) Describe the factors to be considered for the site selection and digester design of a biogas plant and briefly describe the digester design of a biogas plant.

problem 2)a) With a neat sketch, describe the construction and working of a circular fixed dome digester (china) type of biogas plant.

b) With a neat schematic diagram, describe the working of hybrid cycle ocean thermal energy conversion system.

problem 3)a) With a neat schematic diagram, describe the components and working of a tidal power plant.

b) With a neat diagram, describe the power generation from high level reservoir type wave power machine.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M96263

Have any Question? 


Related Questions in Other Engineering

Problem 1a router is used to cut locating notches on a

Problem 1 A router is used to cut locating notches on a printer circuit board. The vibration level at the surface of the board as it is cut, is considered to be a major source of dimensional variation (lower the better) ...

Assignment statementclimate change is a serious challenge

ASSIGNMENT STATEMENT Climate change is a serious challenge to the Kingdom of Saudi Arabia, which is under tremendous pressure as a result of the hyper aridity of the climate, severe shortage in water resources, rapidly g ...

Assignment1 discuss symmetrical conditions in fourier

ASSIGNMENT 1. Discuss symmetrical conditions in Fourier series 2. Derive conversion formulae among different types of Fourier Series 3. State and prove any six properties of Fourier transform. 4. State and prove any four ...

Assignmentactive filter design techniques1refer to chapter

ASSIGNMENT: Active Filter Design Techniques 1. Refer to Chapter 6 in the text as needed. 2. Using the Fast, Practical Filter Design technique presented in section 6.3 design the following. Be sure to show all work for fu ...

Project proposal -objectives to get more familiar with the

Project Proposal - Objectives: To get more familiar with the Hadoop Ecosystem (Spark specifically) and Scala Programming. Resources: Files of tweets about election Project Topic: The election of 2016 seems to be a very c ...

Electronics lab transistor biasing1given a bjt unloaded

Electronics Lab: Transistor Biasing 1. Given a BJT unloaded amplifier shown in figure 1 below with β=100. o Draw DC equivalent circuits of this unloaded amplifier. o Draw the DC load line of the circuit. o Determine the ...

Assignmentradio frequency applications and

Assignment Radio Frequency Applications and Feedback Directions: Please answer BOTH of the questions and respond to a minimum of two of your classmates. Question A Discuss some important op amp parameters needed for radi ...

Process descriptionyour job is to design heat exchanger cl

Process Description Your job is to design heat exchanger Cl for the process to produce aromatics from shale gas. Details of the process have been given in the handouts in CHE 300. Please use the stream and units numbers ...

I need a report on what is a robot and also discuss seven

I need a report on what is a robot and also discuss seven criteria of defining a robot ( using the book robot programming a guide of programming autonomous robots) I need 4 pages not including references.

Time managementdiscuss some of the reasons why individuals

Time Management Discuss some of the reasons why individuals routinely over-estimate the time for project activities. How is this behavior detrimental to the schedule and project? Are some of these reasons more prevalent ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen