Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

problem 1) Describe the ways in which natural ventilation can be achieved in buildings.

problem 2) prepare in brief the conditions in which artificial ventilation is required to be provided.

problem 3) Describe the procedure and data required for the no. of exhaust fans calculation for a kitchen.

problem 4) Which general rules must you observe for artificial ventilation in a building?

problem 5) prepare brief notes on the following:

i) Types of fans used in mechanical ventilation.

ii) Fan coil units.

iii) Types of filters used in Air Conditioning.

iv) Wind Catchers.

v) Condition of comfort.

vi) Window A.C. unit.

problem 6) What is Time of Reverberation? How is reverberation time computed? State the optimum time of reverberation for the following buildings:

i) Cinema theatres.

ii) Music concert hall.

iii) Assembly hall.

iv) Conference room.

problem 7) Describe with the help of neat sketches:

i) Sprinklers and smoke detectors.

ii) Dry and wet risers.

iii) Any four acoustical defects.

iv) Public address system.

v) Effects of plan shapes on hearing conditions within.

v) Methods of cutting off air borne noise.

vi) Two types of fire hydrants

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M95384

Have any Question? 


Related Questions in Other Engineering

Assignment detailsa company is at the start of the process

Assignment Details A company is at the start of the process of designing a new 7 storey office block to be located in Preston (England) with a single stair. The floor to floor height is to be 3.4m with the top storey of ...

Assignmentradio frequency applications and

Assignment Radio Frequency Applications and Feedback Directions: Please answer BOTH of the questions and respond to a minimum of two of your classmates. Question A Discuss some important op amp parameters needed for radi ...

1 for a 77t truck with gross vehicle weight gvw of 136078

1. For a 77t truck with Gross Vehicle Weight (GVW) of 136078 kg with dual rear tyres and a tyre inflation pressure is 120 psi (or 8.43 kg/cm 2 ). Use the equivalent single tyre loading. i. Determine the contact surface a ...

Discussion-please share with your classmates an experience

Discussion- Please share with your classmates an experience where you have dealt with lack of accommodation for the user in the design of equipment, process, or product. What was done to accommodate the user? Which anthr ...

Problem 1find the maximum likelihood ml test for a single

Problem 1. Find the Maximum Likelihood (ML) test for a single observation x(0) to distinguish between H 0 and H 1 if H 0 : P x (0)(x(0)) = 1/2exp (-|x(0)|) H 1 : P x (0)(x(0)) = 1/2exp (-|x(0) - A|) when A > 0. Find the ...

1the emf of a generator of 377 ohm internal impedance is a

1. The EMF of a generator of 377 ohm internal impedance is a 2 ps long pulse of 12 volt amplitude. The generator drives a 10km long section of transmission line of 377 ohm characteristic impedance and 3 x 10 8 m/s propag ...

Assignmentdiscussionanalog integrated circuits amp

Assignment Discussion Analog Integrated Circuits & Lab Op-Amp Application and Datasheets Directions: Please answer BOTH of the questions and respond to a minimum of two of your classmates. Question A Discuss why it is im ...

I have a project about sound detect i am using chipkit

I have a project about sound detect. I am using (ChipKit Max32) as microcontroller and (Bob_09964) as microphones (3 of them to be used) I want the following things: 1- The software codes of (ChipKit Max32) which uses MP ...

Problem 1a router is used to cut locating notches on a

Problem 1 A router is used to cut locating notches on a printer circuit board. The vibration level at the surface of the board as it is cut, is considered to be a major source of dimensional variation (lower the better) ...

C project reportsi have two c program i need one reports

C++ Project Reports I have two C++ program i need one reports for ech one of the and i wnat them to be tn the same format in the instruction if there some the thing not right i will not accept it. The two must be diferen ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen