Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

problem 1)a) What do you mean by electro-deposition? Describe clearly the various factors on which quality of the electro-deposition depends.

b) An electric train starts from rest with a uniform acceleration of 2Kmph/sec for 30 seconds and is moving up a gradient of 1%. The tractive resistance is 40N/tonne. Effect of rotational inertia is 10%. The coasting period is 50 seconds and the braking period is 20 seconds. The station stop is 15 seconds. The combined efficiency of gear and motor is 75%. find out the schedule aped and specific energy consumption.

c) describe the requirements of good heating elements used in electric heating systems?

problem 2)a) List out the various requirements of an ideal traction system.

b) A small piece of wood measuring 8cm×3cm×1cm is placed between two electrodes each measuring 32cm×3cm. The distance between them is 2cm. A voltage at 20MHz is applied to the electrodes for heating the plywood. If the power consumed by the heating process is 2KW, find (i) the voltage applied across the electrodes and (ii) the current through the plywood piece. The plywood has a permittivity of 5 and a power factor of 0.005.

c) Two DC traction motors each having a resistance of 0.3ohm and when connected in parallel across 500V draw a current of 50A each and run at 700rpm and 750rpm respectively. Now, if they are connected in series, each taking a current of 50A on 500V mains, find the speed and voltage across each machine.

problem 3)a) Define the term ‘Welding’. describe with a neat sketch the process of Flash butt welding.

b) describe with a neat sketch the construction and working of a Coreless type high frequency induction furnace.

c) A train weighing 500 tonnes is going down a gradient of 20 in 1,000. It is desired to maintain a speed of 40Kmph by regenerative braking. find out the power fed to the line. The tractive resistance is 40N/tonne, the effect of rotational inertia 10% and efficiency of conversion is 75%.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M96258

Have any Question? 


Related Questions in Other Engineering

Assignmentan embedded system is any electronic system that

Assignment An embedded system is any electronic system that uses a CPU chip but that is not a general-purpose workstation, desktop, or laptop computer. It is a specialized computer system that is part of a larger system ...

Assignmentthe purpose of an antenna in a radio transmitter

Assignment The purpose of an antenna in a radio transmitter is to launch the radio waves into space. In a receiver, the idea is to pick up as much of the transmitter's power as possible and supply it to the tuner. The si ...

Microprocessorsmodule-simple automation systemsoverviewin

MICROPROCESSORS Module-Simple Automation Systems OVERVIEW In the final module, we cut the umbilical cord and try standalone operations of UNO board. You will learn about the applications of the AVR in various areas. We a ...

Problem 1find the maximum likelihood ml test for a single

Problem 1. Find the Maximum Likelihood (ML) test for a single observation x(0) to distinguish between H 0 and H 1 if H 0 : P x (0)(x(0)) = 1/2exp (-|x(0)|) H 1 : P x (0)(x(0)) = 1/2exp (-|x(0) - A|) when A > 0. Find the ...

Problem 1nbspnbspnbspa letnbsphand calculate ab a-b ab ba

Problem 1:    (a) Let  Hand calculate A+B, A-B, AB, BA, CA, CB, and AC T . (b) Use MATLAB to verify your calculations. Problem 2: (a) Let Hand calculate |A|, r A , and A -1 if it exists. (b) Hand calculates the eigenvalu ...

Stting up a xilinx project for the bcd clockobjective

Setting up a Xilinx project for the BCD Clock Objective: This document is intended to be used as a reference guide to aid in setting up and working with a Xilinx ISE WebPACK project for use with the BCD clock project. Pr ...

Microcomputers lab exploring pwmobjectives to gain a better

Microcomputers Lab: Exploring PWM Objectives: To gain a better understanding of Pulse Width Modulation. What you will need: Arduino UNO, Analog Discovery Kit (ADK), LU EE Component Kit, jump wires, a computer with instal ...

Question 1 the two basic kinds of transistor circuits are

Question 1 The two basic kinds of transistor circuits are amplifying and switching. True False Question 2 The bridge rectifier is similar to a full-wave rectifier because it produces a full-wave output voltage. True Fals ...

Electronics lab transistor biasing1given a bjt unloaded

Electronics Lab: Transistor Biasing 1. Given a BJT unloaded amplifier shown in figure 1 below with β=100. o Draw DC equivalent circuits of this unloaded amplifier. o Draw the DC load line of the circuit. o Determine the ...

Risk factors and gantt chartsquestion 1 project risk

Risk Factors and Gantt Charts Question 1: Project Risk factors • List the major risk factors for your project and the possible ways to mitigate this risks for your project. Question 2: Resource Evaluation • Produce and c ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro