Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

Stereotaxic Neurosurgery for Electrode Implant:

problem 1: Using the rat stereotaxic atlas in the course materials, devise a surgical plan for implanting a Michigan type array (Neuronexus) of 16 electrodes into the VL thalamus (ventrolateral thalamic nucleus). Include details about the electrode geometry you choose, the coordinates of the target, which coronal slice you used to determine your target, the coordinates of the craniotomy, where you choose to put your ground and reference wires, and where you will place the connector for the headstage.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M9715

Have any Question? 


Related Questions in Other Engineering

Technical memo based on a provided excel sheetsreport your

Technical MEMO based on a provided excel sheets Report your results to Dr. Robin Hood, Director of Applications Department, in a technical memo, no longer than 3 pages. Note that Dr. Hood has a strong background in fuel ...

Time managementdiscuss some of the reasons why individuals

Time Management Discuss some of the reasons why individuals routinely over-estimate the time for project activities. How is this behavior detrimental to the schedule and project? Are some of these reasons more prevalent ...

Power flow project -figure 1 shows a single-line diagram of

Power Flow Project - Figure 1 shows a single-line diagram of a five-bus power system. Input data are given in Tables 1, 2, and 3. As shown in Table 1, bus 1 is the swing bus, to which a generator is connected. Bus 3 is a ...

I have a project about sound detect i am using chipkit

I have a project about sound detect. I am using (ChipKit Max32) as microcontroller and (Bob_09964) as microphones (3 of them to be used) I want the following things: 1- The software codes of (ChipKit Max32) which uses MP ...

1the emf of a generator of 377 ohm internal impedance is a

1. The EMF of a generator of 377 ohm internal impedance is a 2 ps long pulse of 12 volt amplitude. The generator drives a 10km long section of transmission line of 377 ohm characteristic impedance and 3 x 10 8 m/s propag ...

1 purposethe primary purpose of this project is to help you

1. Purpose The primary purpose of this project is to help you understand the pipelining process for a simple set of MIPS instructions. You will gain experience with basic pipelining principles, as well as the hazard cont ...

Problem 1a router is used to cut locating notches on a

Problem 1 A router is used to cut locating notches on a printer circuit board. The vibration level at the surface of the board as it is cut, is considered to be a major source of dimensional variation (lower the better) ...

Exercise 1charity is a big business in the united states

Exercise 1 Charity is a big business in the United States. The Web site charitynavigator.com gives information on roughly 5500 charitable organizations, and there are many smaller charities that fly below the navigator's ...

Homework consider a renewal process let x be the

Homework Consider a renewal process. Let X be the interrenewal times; and let I and R be the length of an interval interrupted at random and its remainder, respectively. The following BASIC simulation calculates the aver ...

Microprocessors projectoverviewyou are required to complete

MICROPROCESSORS PROJECT Overview You are required to complete a final project for this course. It requires you to build a fully functional prototype of a standalone gadget which will be an alarm clock and will also displ ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro