Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

Task 1: Through the measurement of electrical conductivity of waste-water one can find out the:

a) Oxygen content.
b) Concentration of total ions.
c) Acidity.
d) Heavy metal content.
e) Concentration of organic acids.

Task 2: In the inflow to a municipal wastewater treatment plant the COD = 1000 mg/l and the BOD5 = 500 mg/l. From such figures it can be recognized that one is concerned with:

a) Industrial and domestic waste-water.
b) Domestic waste-water with a high proportion of inorganic content substances from a dairy.
c) The typical properties of municipal waste-water.
d) A big amount of storm water and a very little domestic wastewater.
e) A big amount of groundwater and precipitation water mixed altogether with 20 % domestic waste-water

Task 3: Nitrogen is present in wastewater in different forms and compounds. Which of the listed ‘parameters’ is a pure organic composition?

a) Kjeldahl nitrogen (TKN)
b) Amino acid
c) Uric acid (C5H4N4 = O3)
d) Total nitrogen (totalN)
e) Nitrogen in total (Ntot)

Task 4: As infiltration water one designates the inflow into the sewer system of:

a) Damaging commercial or industrial waste-water.
b) Unapproved connections.
c) Water that runs in from roof and courtyard surfaces.
d) Groundwater that penetrates via leaks and drains.
e) Flushing water that is used for sewer cleaning.

Task 5: A dry weather inflow (Qdw) is 100 litres/s. In this there is an infiltration component (Qinf) of 30 %.

a) How many m3 is the infiltration water inflow per day?

b) What persuade has a higher infiltration water component on the operation of the waste-water treatment plant?

Task 6: The quantity of wastewater flowing from a combined system to a waste-water treatment plant with 100,000 inhabitants can be taken from the given diagram.

a) How big is the quantity of dry weather water?

b) According to the diagram, how much water can the plant accept as a maximum?

c) How big is the specific wastewater component (m3/(I x d)) of this waste-water treatment plant?

d) Why does this value deviate from the mean specific water consumption (m3/(I x d))?

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M95790

Have any Question? 


Related Questions in Other Engineering

I need a report on what is a robot and also discuss seven

I need a report on what is a robot and also discuss seven criteria of defining a robot ( using the book robot programming a guide of programming autonomous robots) I need 4 pages not including references.

Assignment automated teller machine atmon an automated

Assignment: Automated Teller Machine (ATM) On an automated teller machine (ATM), the customer is identified by inserting a plastic ATM card with a magnetic stripe or a plastic smart card with a chip that contains a uniqu ...

Electronics assignment1 using pspice simulation print the

Electronics Assignment 1. Using PSpice simulation, print the waveforms of the following values for the circuit below (V S =100 mVpp, 1kHz). You can choose any npn transistor for the transistors in the circuit. a. Operati ...

Biomedical engineering modelling amp analysis assignment

Biomedical Engineering Modelling & Analysis Assignment - Aim and Learning Outcomes: To use appropriate software to solve a set of differential equations related to a topical engineering problem and use the solutions to m ...

1 estimate the cycle time and production of a caterpillar

1. Estimate the cycle time and production of a Caterpillar 777D flat floor off highway truck operating on a level haul road of 4000m length. The road is a rutted dirt roadway with no maintenance and no stabilisation, tyr ...

Risk factors and gantt chartsquestion 1 project risk

Risk Factors and Gantt Charts Question 1: Project Risk factors • List the major risk factors for your project and the possible ways to mitigate this risks for your project. Question 2: Resource Evaluation • Produce and c ...

Question 1 the two basic kinds of transistor circuits are

Question 1 The two basic kinds of transistor circuits are amplifying and switching. True False Question 2 The bridge rectifier is similar to a full-wave rectifier because it produces a full-wave output voltage. True Fals ...

Electronics lab transistor biasing1given a bjt unloaded

Electronics Lab: Transistor Biasing 1. Given a BJT unloaded amplifier shown in figure 1 below with β=100. o Draw DC equivalent circuits of this unloaded amplifier. o Draw the DC load line of the circuit. o Determine the ...

Power flow project -figure 1 shows a single-line diagram of

Power Flow Project - Figure 1 shows a single-line diagram of a five-bus power system. Input data are given in Tables 1, 2, and 3. As shown in Table 1, bus 1 is the swing bus, to which a generator is connected. Bus 3 is a ...

Assignment - audio connectivity and interface techniques

Assignment - Audio connectivity and interface techniques Tasks Background information This assignment allows learners to demonstrate their knowledge and practical ability in connecting together analogue and digital syste ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro