Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

problem 1:

prepare down a brief note on whirl gate.

problem 2:

What is ideal profile of the sprue? Illustrate out how it is actually practiced.

problem 3:

Illustrate the cleaning procedures which should be carried out on a bronze casting to be employed for decorative purposes.

problem 4:

Illustrate the principle of permanent mould casting with their applications.

problem 5:

Provide advantages and drawbacks of permanent mould casting compared to that of the sand casting.

problem 6:

Illustrate out the advantages of pouring metal as cold as probable.

problem 7:

Illustrate the relative demerits and merits of different non destructive methods.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M911082

Have any Question? 


Related Questions in Other Engineering

Life cycle and risk management assignment 4 a

Life Cycle and Risk Management Assignment 4: A workplace-based report This assessment task involves collaborative team arrangement efforts and designed to explore the key issues of risk management and how these issues ar ...

A steam from a steame generator at 160 bar 540degc having a

A steam, from a steame generator at 160 bar, 540 ° C having a flow rate of 400 kg/s expands in a high pressure turbine with an isentropic efficiency of 90% to 40 bar. A 16 % of the exhaust steam is used for feedwater hea ...

Assignmentsuppose a large aerospace engineering firm has

Assignment Suppose a large aerospace engineering firm has immediately hired you as a consultant to investigate a potential violation of corporate policy and data theft. You have been informed that an employee may have be ...

Life cycle and risk management assignment 3 a

Life Cycle and Risk Management Assignment 3: A workplace-based report This assessment task involves collaborative team arrangement efforts and designed to explore engineering asset management as a system incorporating li ...

Risk factors and gantt chartsquestion 1 project risk

Risk Factors and Gantt Charts Question 1: Project Risk factors • List the major risk factors for your project and the possible ways to mitigate this risks for your project. Question 2: Resource Evaluation • Produce and c ...

Assignmentpart 1bullop-amp introduction1read chapters 1-2

Assignment Part 1 • Op-Amp Introduction 1. Read Chapters 1-2 in the text Op Amps for Everyone Fourth Edition 2. For the configuration below: 3. o With Vin = 4Vrms, f = 1kHz answer the following for each case: o Calculate ...

Ac models1the impedance of a capacitor is inversely

AC Models 1. The impedance of a capacitor is inversely proportional to the frequency and the capacitor effectively blocks dc voltage. a. True b. False 2. A coupling capacitor couples an ac signal into an amplifier withou ...

Stting up a xilinx project for the bcd clockobjective

Setting up a Xilinx project for the BCD Clock Objective: This document is intended to be used as a reference guide to aid in setting up and working with a Xilinx ISE WebPACK project for use with the BCD clock project. Pr ...

Diode circuits1 the 6v zener diode below has zero zener

Diode Circuits 1. The 6V zener diode below has zero Zener resistance and a knee current of 5mA.The minimum value of R, so that the voltage across it does not fall below 6V is 2. A zener diode in the circuit shown in belo ...

Finite element analysis in engineering term assignmentfor

Finite Element Analysis in Engineering Term Assignment For the truss system above, do the following. Q1: (a) Solve for the x,y components of displacement of each joint using one bar element for each link. Show all work i ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen