+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1) describe with neat diagrams, the stratigraphic control of the sealing of fault traps.

problem 2) prepare down the characteristics of folds important to petroleum geologist and describe with neat figures, cross folding and multiple axes in relation to closure.

problem 3) describe recognition of subsurface unconformities and describe relation of unconformities to traps for oil and gas production. Comment on effect of unconformities on oil and gas prospects.

problem 4) What are Reconnaissance and detail maps? How much errors are permissible in their construction.

problem 5) prepare notes on the following:

a) Mental factors in wild catting.

b) Flowage or stretching during folding.

c) Piedment scraps.

d) Truncation.

e) Fractures as reservoir rocks

problem 6) Out line origin of saltdomes, with reference to model studies.

problem 7) What are buried hills? Describe with neat figures, traps within, around and over buried hills.

problem 8) prepare notes on the following:

a) Reversal due to faulting.

b) Strike overlap.

c) Closures produced by intersecting faults.

d) Geologic and areal maps.

e) Structural conditions favouring production from fractures.

Other Engineering, Engineering

• Category:- Other Engineering
• Reference No.:- M95322

Have any Question?

## Related Questions in Other Engineering

### Problem 1nbspnbspnbspa letnbsphand calculate ab a-b ab ba

Problem 1:    (a) Let  Hand calculate A+B, A-B, AB, BA, CA, CB, and AC T . (b) Use MATLAB to verify your calculations. Problem 2: (a) Let Hand calculate |A|, r A , and A -1 if it exists. (b) Hand calculates the eigenvalu ...

### Short answers of 150-400 words1 engineering and

Short answers of 150-400 words 1. Engineering and architecture are two fields of knowledge that continually intersect and bifurcate in the period that we have been studying. What is relationship between architecture and ...

### C project reportsi have two c program i need one reports

C++ Project Reports I have two C++ program i need one reports for ech one of the and i wnat them to be tn the same format in the instruction if there some the thing not right i will not accept it. The two must be diferen ...

### Life cycle and risk management assignment 3 a

Life Cycle and Risk Management Assignment 3: A workplace-based report This assessment task involves collaborative team arrangement efforts and designed to explore engineering asset management as a system incorporating li ...

### Problem 1a router is used to cut locating notches on a

Problem 1 A router is used to cut locating notches on a printer circuit board. The vibration level at the surface of the board as it is cut, is considered to be a major source of dimensional variation (lower the better) ...

### Diode circuits1 the 6v zener diode below has zero zener

Diode Circuits 1. The 6V zener diode below has zero Zener resistance and a knee current of 5mA.The minimum value of R, so that the voltage across it does not fall below 6V is 2. A zener diode in the circuit shown in belo ...

### Assignmentwhy program design is importantanswer the

Assignment Why Program Design is Important? Answer the following questions: 1. What is a program design? 2. Why program design is important? 3. What program design tools are available? Discuss in details by studying at l ...

### Create the single line diagram of a substation having the

Create the single line diagram of a substation having the following equipments using a drawing software. You can use any drawing software available (e.g. Smartdraw, MS Visio, Microstation, AUTOCAD, Edraw etc.). -Incoming ...

### Lab ac modelsintroductionthe lab is based on the ac models

Lab: AC Models Introduction: The lab is based on the AC models of a transistors. After the transistor has been biased with a Q-point near the middle of the load line, we can couple a small AC voltage into the base. This ...

### Microprocessorsmodule-simple automation systemsoverviewin

MICROPROCESSORS Module-Simple Automation Systems OVERVIEW In the final module, we cut the umbilical cord and try standalone operations of UNO board. You will learn about the applications of the AVR in various areas. We a ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

### Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen