Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

problem 1)a) describe the well design considerations for high pressure, high temperature deep drilling program. prepare down the possible challenges and solution in brief.

b) describe the step by step operation of lowering TGB and drilling 30º hole and lowering structural casing and cementation in deep water drilling with appropriate sketches.

problem 2)a) Compute new kG if rig displacement of 21000 Tons and kG of 58 feet. A weight of 180 tons with VCG of 11 ft is moved to VCG of 167 ft.

b) describe different mathematical equations to find out wind, wave and current forces acting on offshore structures. State and describe assumptions and parameters of these equations.

problem 3)a) describe Lower Marine Riser Pack (LMRP). Draw typical subsea BOP stack with LMRP.

b) describe Dynamic Positioning System of station keeping in detail

problem 4)a) prepare brief notes on:

i) Subsea Diving System.

ii) Riser design considerations.

b) Draw neat schematic diagram of a, ‘typical subsea well completion system.’ Indicate all the features.

problem 5)a) What is tension leg platform? describe design considerations in brief, for the same.

b) Describe tubular joint classification in brief with suitable sketch.

problem 6)a) What is well cementation? Describe a typical well cementation programme for deep water (offshore) well.

b) prepare down the types of subsea horizontal trees in detail.

problem 7) prepare brief notes on:

a) Marine terminals and transport.

b) Offshore safety.

c) Forces and motions acting on fixed platform.

problem 8)a) describe in detail productive formation testing methods, in brief.

b) Describe design consideration in oil and gas pipeline.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M95724

Have any Question? 


Related Questions in Other Engineering

I have a project about sound detect i am using chipkit

I have a project about sound detect. I am using (ChipKit Max32) as microcontroller and (Bob_09964) as microphones (3 of them to be used) I want the following things: 1- The software codes of (ChipKit Max32) which uses MP ...

A steam from a steame generator at 160 bar 540degc having a

A steam, from a steame generator at 160 bar, 540 ° C having a flow rate of 400 kg/s expands in a high pressure turbine with an isentropic efficiency of 90% to 40 bar. A 16 % of the exhaust steam is used for feedwater hea ...

1 purposethe primary purpose of this project is to help you

1. Purpose The primary purpose of this project is to help you understand the pipelining process for a simple set of MIPS instructions. You will gain experience with basic pipelining principles, as well as the hazard cont ...

Assignmentradio frequency applications and

Assignment Radio Frequency Applications and Feedback Directions: Please answer BOTH of the questions and respond to a minimum of two of your classmates. Question A Discuss some important op amp parameters needed for radi ...

1 for a 77t truck with gross vehicle weight gvw of 136078

1. For a 77t truck with Gross Vehicle Weight (GVW) of 136078 kg with dual rear tyres and a tyre inflation pressure is 120 psi (or 8.43 kg/cm 2 ). Use the equivalent single tyre loading. i. Determine the contact surface a ...

Biomedical engineering modelling amp analysis assignment

Biomedical Engineering Modelling & Analysis Assignment - Aim and Learning Outcomes: To use appropriate software to solve a set of differential equations related to a topical engineering problem and use the solutions to m ...

Electronics assignment1 using pspice simulation print the

Electronics Assignment 1. Using PSpice simulation, print the waveforms of the following values for the circuit below (V S =100 mVpp, 1kHz). You can choose any npn transistor for the transistors in the circuit. a. Operati ...

Microprocessors projectoverviewyou are required to complete

MICROPROCESSORS PROJECT Overview You are required to complete a final project for this course. It requires you to build a fully functional prototype of a standalone gadget which will be an alarm clock and will also displ ...

Assignmentan embedded system is any electronic system that

Assignment An embedded system is any electronic system that uses a CPU chip but that is not a general-purpose workstation, desktop, or laptop computer. It is a specialized computer system that is part of a larger system ...

1 simplify the expressions using boolean algebra and its

1. Simplify the expressions using Boolean algebra and its identities: X'Y + XYZ' + Y' + XZ (Y+Y') = 1 2. The academic director wants to select students in Sydney Study Center to give them Gala Dinner Award. The recipient ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen