Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

problem 1) describe in details the conventional resistivity logging method with reference to principle, devices used, log presentation and application.

problem 2) describe in brief the different components of wire line logging equipments with neat diagram.

problem 3) Describe temperature logging with reference to objectives, principle, properties measured and applications.

problem 4) Describe how focussed electrode logs are useful over conventional resistivity logs. Describe the principle, equipment, depth of investigation, vertical resolution and application of Laterolog 7.

problem 5) prepare short notes on the following:

a) What are the constituents of MWD and its importance.

b) Application of caliper logging.

c) Parameters of importance in “logging environment”.

d) Shale potential.

e) Delaware effect.

problem 6) Describe the working principle of spectral Gamma Ray log, its qualitative and quantitative use.

problem 7) Describe induction logging with reference to objectives, properties measured, principle, equipment, optimum logging, conditions.

problem 8) Answer the following:

a) Describe the factors affecting shape and amplitude of SP curves.

b) Microspherically focussed logs.

c) Sequence of events in simple DST and its application.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M95334

Have any Question? 


Related Questions in Other Engineering

Assignment1 discuss symmetrical conditions in fourier

ASSIGNMENT 1. Discuss symmetrical conditions in Fourier series 2. Derive conversion formulae among different types of Fourier Series 3. State and prove any six properties of Fourier transform. 4. State and prove any four ...

Assignmentradio frequency applications and

Assignment Radio Frequency Applications and Feedback Directions: Please answer BOTH of the questions and respond to a minimum of two of your classmates. Question A Discuss some important op amp parameters needed for radi ...

Electronics lab transistor biasingdiscuss what transistor

Electronics Lab: Transistor Biasing Discuss what "transistor biasing" means and its importance to transistor circuit design. Choose one type of biasing, and explain either how it works or its advantages and disadvantages ...

1the emf of a generator of 377 ohm internal impedance is a

1. The EMF of a generator of 377 ohm internal impedance is a 2 ps long pulse of 12 volt amplitude. The generator drives a 10km long section of transmission line of 377 ohm characteristic impedance and 3 x 10 8 m/s propag ...

1 for a 77t truck with gross vehicle weight gvw of 136078

1. For a 77t truck with Gross Vehicle Weight (GVW) of 136078 kg with dual rear tyres and a tyre inflation pressure is 120 psi (or 8.43 kg/cm 2 ). Use the equivalent single tyre loading. i. Determine the contact surface a ...

Assignmentan embedded system is any electronic system that

Assignment An embedded system is any electronic system that uses a CPU chip but that is not a general-purpose workstation, desktop, or laptop computer. It is a specialized computer system that is part of a larger system ...

Microcomputers lab exploring pwmobjectives to gain a better

Microcomputers Lab: Exploring PWM Objectives: To gain a better understanding of Pulse Width Modulation. What you will need: Arduino UNO, Analog Discovery Kit (ADK), LU EE Component Kit, jump wires, a computer with instal ...

Finite element analysis in engineering term assignmentfor

Finite Element Analysis in Engineering Term Assignment For the truss system above, do the following. Q1: (a) Solve for the x,y components of displacement of each joint using one bar element for each link. Show all work i ...

Introduction to signal analysis project music

Introduction to Signal Analysis Project: Music Synthesis Project Definition: The objective of this project is to synthesize musical signals. You will generate harmonic tones and use them to perform well-known melodies. M ...

Discussion-please share with your classmates an experience

Discussion- Please share with your classmates an experience where you have dealt with lack of accommodation for the user in the design of equipment, process, or product. What was done to accommodate the user? Which anthr ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen