Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Chemical Engineering Expert

A)  Draw the expected DSC graph for a semicrystalline polymer heated from 25-300°C at 5°C/min with the following properties:

• % crystallinty of initial sample = 25%

• Heat capacity of the polymer generally decreases between room temperature and Tg

• Tg = 120°C

• There is a small amount of enthalpic recovery

• The sample’s heat capacity is constant above Tg

• Cold crystallization occurs between 140-150°C and adds 25% crystallinity to the sample

• The sample melts between 200-220°C

• The sample begins to degrade via an exothermic reaction at 270°C

• The heat of crystallization of a perfect crystal of this polymer is 100 J/g

For your answer, you should draw a graph and label the axes with appropriate quantities and units (the X axis should be temperature).  Draw the expected response and use arrows and/or other annotation to illustrate the various features.  Include as much detail as possible.

Chemical Engineering, Engineering

  • Category:- Chemical Engineering
  • Reference No.:- M91893

Have any Question? 


Related Questions in Chemical Engineering

Potential difference and resistance a conducting sphere of

Potential difference and resistance. A conducting sphere of radius a, with conductivity u is cut into two hemispheres. Then, each hemisphere is trimmed so that it has a flat surface on top and the two sections are connec ...

According to experimental results for parallel airflow over

According to experimental results for parallel airflow over a uniform temperature, heated vertical plate, the effect of free convection on the heat transfer convection coefficient will be 5% when GrL/Re2L = 0.08. Conside ...

A wing generates a lift l when moving through sea-level air

A wing generates a lift L when moving through sea-level air with a velocity U. How fast must the wing move through the air at an altitude of 35,000 ft if it is to generate the same lift? (Assume the lift coefficient is c ...

A potential flow source having an intensity of 10m2s placed

A potential flow source having an intensity of 10m2/s, placed in the point of Cartesian coordinates (1;0), and a sink having identical intensity, placed in the point (-1;0), are combined with a uniform flow at 25 m/s, in ...

1 100 moles of a fuel containing methane and butane is

1. 100 moles of a fuel containing methane and butane is burned with 25% excess air in a furnace producing stack gas at 300C and 105 kPa. Determine the amount of 100 psi saturated steam that can be produced from water fed ...

A well is producing from a saturated oilreservoir with an

A well is producing from a saturated oilreservoir with an average reservoir pressureof 3000 psig. Stabilized flow test dataindicates that the well is capable of producing400 STB/day at a bottom-holeflowing pressure of 25 ...

Q1 water is used to absorb the vapor of methanol at 300 k

Q1. Water is used to absorb the vapor of methanol at 300 K and 101.325 kPa. The concentration of methanol in both gas and liquid phases are very low, with the equilibrium relation following Henry's Law. The known paramet ...

A solar collector design consists of an inner tube enclosed

A solar collector design consists of an inner tube enclosed concentrically in an outer tube that is transparent to solar radiation. The tubes are thin walled with inner and outer diameters of 0.10 and 0.15 m, respectivel ...

A horizontal 25-mm diameter cylinder is maintained at a

A horizontal, 25-mm diameter cylinder is maintained at a uniform surface temperature of 35°C. A fluid with a velocity of 0.05 m/s and temperature of 20°C is in cross flow over the cylinder. Determine whether heat transfe ...

A well is producing from a saturated oilreservoir with an

A well is producing from a saturated oilreservoir with an average reservoir pressureof 3000 psig. Stabilized flow test dataindicates that the well is capable of producing400 STB/day at a bottom-holeflowing pressure of 25 ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen