Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

1) Describe the structure of incompressible turbulent flows of an atmospheric boundary layer with the help of suitable diagram.

2) describe the effect of terrain on gradient height with labelled sketch.

3) describe significant differences between the horizontal axis and vertical axis wind energy collectors.

4) describe what is Betz coefficient? describe how it is find outd by the momentum theory?

5) Define the following terms:

a) Aerodynamics of the trains

b) Estimation of drag coefficients of automobiles.

6)  Discuss the effects of cutback angle in vehicle aerodynamics.prepare briefly a note on the aerodynamics of Hovercraft.

7) describe the pressure distribution on the typical low rise buildings. How do you evaluate the aerodynamic loads on such buildings? describe the factors that are involved in the design of the building ventilation?

8) describe how are special aerodynamic problems pertaining to the tall buildings dealt with? Provide an account of environmental winds in the city blocks.

9) Explailn the effect of Reynold’s number over the shape and size of wake made behind the bluff bodies facing the uniform free stream. Make out the important attributes of external flow over body surface involving the flow separation.

10) describe the following topics in brief:

a) Stall flutter

b) Vortex induced vibrations.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M912323
  • Price:- $90

Guranteed 48 Hours Delivery, In Price:- $90

Have any Question? 


Related Questions in Other Engineering

System administration assignment-aim the aim of this

System Administration Assignment- Aim: The aim of this assignment is to become familiar with subnet masking and designing small networks for fictitious organizations. Task: Imagine you work for a firm which provides syst ...

Lab ac modelsintroductionthe lab is based on the ac models

Lab: AC Models Introduction: The lab is based on the AC models of a transistors. After the transistor has been biased with a Q-point near the middle of the load line, we can couple a small AC voltage into the base. This ...

The presentation should cover the followingslide show give

The presentation should cover the following; Slide show Give information on structure Recalls on any appliances 4 questions you would want to ask the firefighters and homeowner hypothesis 10-15 minutes nfpa 921 worksheet ...

Assignmentfor the circuit below perform the following1given

Assignment For the circuit below, perform the following: 1. Given an AC input voltage of Vrms = 200Vrms and a sinusoidal frequency of omega = 120pi rad/sec, determine the following: o V1peak (peak value of AC input volta ...

1the emf of a generator of 377 ohm internal impedance is a

1. The EMF of a generator of 377 ohm internal impedance is a 2 ps long pulse of 12 volt amplitude. The generator drives a 10km long section of transmission line of 377 ohm characteristic impedance and 3 x 10 8 m/s propag ...

Design a voltage-divider biased common source amplifier

Design a voltage-divider biased common source amplifier with no bypass(JFET) Design a voltage-divider biased common source amplifier with no bypass to the following specifications: Av (overall) = -3, Rsrc = 30 kΩ, Rin = ...

Microcomputers lab exploring pwmobjectives to gain a better

Microcomputers Lab: Exploring PWM Objectives: To gain a better understanding of Pulse Width Modulation. What you will need: Arduino UNO, Analog Discovery Kit (ADK), LU EE Component Kit, jump wires, a computer with instal ...

1 estimate the cycle time and production of a caterpillar

1. Estimate the cycle time and production of a Caterpillar 777D flat floor off highway truck operating on a level haul road of 4000m length. The road is a rutted dirt roadway with no maintenance and no stabilisation, tyr ...

Assignmentradio frequency applications and

Assignment Radio Frequency Applications and Feedback Directions: Please answer BOTH of the questions and respond to a minimum of two of your classmates. Question A Discuss some important op amp parameters needed for radi ...

Electronics assignment1 using pspice simulation print the

Electronics Assignment 1. Using PSpice simulation, print the waveforms of the following values for the circuit below (V S =100 mVpp, 1kHz). You can choose any npn transistor for the transistors in the circuit. a. Operati ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen