Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

1) Describe the coal handling system in detail.

2) Describe about any two dust collectors with the help of neat sketch.

3) Specify the various kinds of cooling towers. Describe any two cooling towers with the help of neat sketch.

4) Compute the boiler thermal efficiency, if the boiler produces 20,000 kg of steam at 10 bar dry and saturated. The amount of coal used is 2000 kg and the calorific value of coal is 36,000 kJ/kg. The feed water enthalpy is 448 kJ/kg.

5) Develop a sketch, describe the closed cycle and open cycle gas turbine.

6) Describe the several elements of nuclear reactor briefly.

7) describe photovoltaic cells with the help of neat sketch.

8) Draw and specify the tidal power plants.

9) A power plant supplies the following loads to customers:

Time in hrs         0 -5     5 - 9     9 - 12     12 -17     17 - 20     20 – 22    22 - 24
Load in MW         30       60         75          50            90               80             50

a) Sketch the load curve

b) Find the load factor of the power plant and energy consumed during 24 hours.

10) Describe the treatment of waste water from the demineralization plant in order to control the water pollution.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M913611

Have any Question? 


Related Questions in Other Engineering

Risk factors and gantt chartsquestion 1 project risk

Risk Factors and Gantt Charts Question 1: Project Risk factors • List the major risk factors for your project and the possible ways to mitigate this risks for your project. Question 2: Resource Evaluation • Produce and c ...

1the emf of a generator of 377 ohm internal impedance is a

1. The EMF of a generator of 377 ohm internal impedance is a 2 ps long pulse of 12 volt amplitude. The generator drives a 10km long section of transmission line of 377 ohm characteristic impedance and 3 x 10 8 m/s propag ...

Assignmentsuppose a large aerospace engineering firm has

Assignment Suppose a large aerospace engineering firm has immediately hired you as a consultant to investigate a potential violation of corporate policy and data theft. You have been informed that an employee may have be ...

1 for a 77t truck with gross vehicle weight gvw of 136078

1. For a 77t truck with Gross Vehicle Weight (GVW) of 136078 kg with dual rear tyres and a tyre inflation pressure is 120 psi (or 8.43 kg/cm 2 ). Use the equivalent single tyre loading. i. Determine the contact surface a ...

Q1 a hollow circular mild steel column of external diameter

Q1. A hollow circular mild steel column of external diameter 300 mm and internal diameter of 250 mm carries an axial load of 1500 kN. a) Determine the compressive stress in the column. b) If the initial length of the col ...

Microprocessors projectoverviewyou are required to complete

MICROPROCESSORS PROJECT Overview You are required to complete a final project for this course. It requires you to build a fully functional prototype of a standalone gadget which will be an alarm clock and will also displ ...

Time managementdiscuss some of the reasons why individuals

Time Management Discuss some of the reasons why individuals routinely over-estimate the time for project activities. How is this behavior detrimental to the schedule and project? Are some of these reasons more prevalent ...

Crude oil is transported from tank farm in yanbu to the

Crude oil is transported from tank farm in Yanbu to the Power plant of the Electric Company in Rabig by ships. Investigate the feasibiliy of building a pipeline system complete pumping system to transport crude oil from ...

1 your boss wants to modify an aircraft by stretching the

1. Your boss wants to modify an aircraft by stretching the fuselage, but only forward of the cg, by a length al. The fuselage has a circular cross section of diameter d. Estimate how much you need to increase the planfor ...

Assignment - audio connectivity and interface techniques

Assignment - Audio connectivity and interface techniques Tasks Background information This assignment allows learners to demonstrate their knowledge and practical ability in connecting together analogue and digital syste ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen