Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

Answer the following problems.

problem 1) describe sedimentary environment. Give the concept and tabular classification of environment. describe marine environment.

problem 2) Describe Walther’s Law. describe sub surface environmental interpretation with appropriate exs.

problem 3) What are flow regime? Give the concept of flow regime. Outline the characteristics of lower flow regime. describe the bedform associated with it.

problem 4) prepare notes on the following:

a) Rhythmites.

b) Mud and Sand volcano.

c) Classification and origin of siliceous rocks.

d) Composition and rock grading of conglomerate.

e) Application of sedimentology in petroleum exploration.

problem 5) Define diagenesis. describe diagenetic changes in the sediments add a note on Compaction and Solution.

problem 6) describe the significance of sequence in environmental reconstruction.

problem 7) prepare detail notes on the following:

a) Diagnosis of sedimentary facies.

b) Reservoir Heterogeneity.

c) Chemical processes of sedimentation.

d) Longshore bar cross bedding.

e) Classification and origin of carbonaceous rocks.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M95318

Have any Question? 


Related Questions in Other Engineering

Design and build a counter that can display the sequence

Design and build a counter that can display the sequence assigned to you by the instructor (see table below). Use two J-K flip-flops for the two most significant bits and two D flip-flops for the two least significant bi ...

Time managementdiscuss some of the reasons why individuals

Time Management Discuss some of the reasons why individuals routinely over-estimate the time for project activities. How is this behavior detrimental to the schedule and project? Are some of these reasons more prevalent ...

Power flow project -figure 1 shows a single-line diagram of

Power Flow Project - Figure 1 shows a single-line diagram of a five-bus power system. Input data are given in Tables 1, 2, and 3. As shown in Table 1, bus 1 is the swing bus, to which a generator is connected. Bus 3 is a ...

Microcomputers lab exploring pwmobjectives to gain a better

Microcomputers Lab: Exploring PWM Objectives: To gain a better understanding of Pulse Width Modulation. What you will need: Arduino UNO, Analog Discovery Kit (ADK), LU EE Component Kit, jump wires, a computer with instal ...

1 your boss wants to modify an aircraft by stretching the

1. Your boss wants to modify an aircraft by stretching the fuselage, but only forward of the cg, by a length al. The fuselage has a circular cross section of diameter d. Estimate how much you need to increase the planfor ...

Process descriptionyour job is to design heat exchanger cl

Process Description Your job is to design heat exchanger Cl for the process to produce aromatics from shale gas. Details of the process have been given in the handouts in CHE 300. Please use the stream and units numbers ...

Assignmentpart 1bullop-amp introduction1read chapters 1-2

Assignment Part 1 • Op-Amp Introduction 1. Read Chapters 1-2 in the text Op Amps for Everyone Fourth Edition 2. For the configuration below: 3. o With Vin = 4Vrms, f = 1kHz answer the following for each case: o Calculate ...

Risk factors and gantt chartsquestion 1 project risk

Risk Factors and Gantt Charts Question 1: Project Risk factors • List the major risk factors for your project and the possible ways to mitigate this risks for your project. Question 2: Resource Evaluation • Produce and c ...

I need a report on what is a robot and also discuss seven

I need a report on what is a robot and also discuss seven criteria of defining a robot ( using the book robot programming a guide of programming autonomous robots) I need 4 pages not including references.

1 the 2d diffusion equation ut dnabla2u is discretized

1. The 2D diffusion equation u t = D∇ 2 u is discretized using the Finite Difference method as (u i,j n+1 - u i,j n )/DΔt = γ[(u i+1 n+1 ,j - 2u i,j n+1 + u i-1 n+1 ,j )/Δx 2 + u i,j+1 n+1 ,j - 2u i,j n+1 + u i-1 n+1 /Δy ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen