Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

1) prepare a brief notes regarding the following points:

a) Pollution

b) Pollutants

c) Classification of pollutant

d) Types of pollution

2) describe the sources for the air pollution? prepare down the effects of air pollution upon the human health.

3) Describe about different types of water pollution in detail.

4) Describe regarding the measurement of the following:

a) Odour of water

b) Chlorine Demand

c) Solids present

d) Acidity and Alkalinity

5) Describe the softening of water in detail.

6) Describe the treatment of the municipal water supply.

7) describe the types of noise pollution? prepare down the effects of the noise pollution.

8) Describe the sources of the radioactive pollution? Discuss each in detail.

9) prepare down the different approaches for controlling the water pollution.

10) prepare down the different approaches for controlling the noise pollution.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M912314

Have any Question? 


Related Questions in Other Engineering

Question 1 the two basic kinds of transistor circuits are

Question 1 The two basic kinds of transistor circuits are amplifying and switching. True False Question 2 The bridge rectifier is similar to a full-wave rectifier because it produces a full-wave output voltage. True Fals ...

Electronics i and labbridge rectifierintroductionthe lab is

Electronics I and Lab Bridge Rectifier Introduction: The lab is based on the previous lab from week 2 on half-wave and full-wave rectifiers and taking that knowledge to build a bridge rectifier. Materials and Equipment: ...

Q1 a hollow circular mild steel column of external diameter

Q1. A hollow circular mild steel column of external diameter 300 mm and internal diameter of 250 mm carries an axial load of 1500 kN. a) Determine the compressive stress in the column. b) If the initial length of the col ...

Problem 1a router is used to cut locating notches on a

Problem 1 A router is used to cut locating notches on a printer circuit board. The vibration level at the surface of the board as it is cut, is considered to be a major source of dimensional variation (lower the better) ...

Design a voltage-divider biased common source amplifier

Design a voltage-divider biased common source amplifier with no bypass(JFET) Design a voltage-divider biased common source amplifier with no bypass to the following specifications: Av (overall) = -3, Rsrc = 30 kΩ, Rin = ...

1the emf of a generator of 377 ohm internal impedance is a

1. The EMF of a generator of 377 ohm internal impedance is a 2 ps long pulse of 12 volt amplitude. The generator drives a 10km long section of transmission line of 377 ohm characteristic impedance and 3 x 10 8 m/s propag ...

Assignment automated teller machine atmon an automated

Assignment: Automated Teller Machine (ATM) On an automated teller machine (ATM), the customer is identified by inserting a plastic ATM card with a magnetic stripe or a plastic smart card with a chip that contains a uniqu ...

Assignmentdiscussionanalog integrated circuits amp

Assignment Discussion Analog Integrated Circuits & Lab Filter Design Directions: Please answer BOTH of the questions and respond to a minimum of two of your classmates. Question A Discuss the various compromises that mus ...

Technical comminucations englpart 1take-away please respond

Technical Comminucations ENGL Part 1 "Take-Away" Please respond to the following: Imagine it is 10 years from today. Identify two things you learned in this course that you couldn't have imagined being successful without ...

Assignmentactive filter design techniques1refer to chapter

ASSIGNMENT: Active Filter Design Techniques 1. Refer to Chapter 6 in the text as needed. 2. Using the Fast, Practical Filter Design technique presented in section 6.3 design the following. Be sure to show all work for fu ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro