Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

1. describe why Low carbon steel in tile normalised condition is stronger than tile same steel ill tile annealed condition.

2. Case carburizing heat treatment is not usually carried out for medium carbon steels. describe why?

3. What do you mean by "critical cooling rate" in hardening of steels?

4. What do you mean by "heat treatment"? prepare down its purpose.

5. prepare down the factors affecting the CCR?

6. What do you mean by normalizing? describe its purpose.

7. What do you mean by quenching? prepare down some of the quenching medium.

8. prepare downthe factors affecting the hardness?

9. What do you mean by hardnability? prepare down the factors affecting it?

10. What do you mean by induction hardening?

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M912026

Have any Question? 


Related Questions in Other Engineering

Power flow project -figure 1 shows a single-line diagram of

Power Flow Project - Figure 1 shows a single-line diagram of a five-bus power system. Input data are given in Tables 1, 2, and 3. As shown in Table 1, bus 1 is the swing bus, to which a generator is connected. Bus 3 is a ...

Assignmentthe purpose of an antenna in a radio transmitter

Assignment The purpose of an antenna in a radio transmitter is to launch the radio waves into space. In a receiver, the idea is to pick up as much of the transmitter's power as possible and supply it to the tuner. The si ...

This homework is part of a private kaggle competition in

This homework is part of a private Kaggle competition, in the end we only want to submit an excel file with ID and Expected column, and I need the R code as well to submit. I am attaching the data files, both should be u ...

Assignmentdiscussionanalog integrated circuits amp

Assignment Discussion Analog Integrated Circuits & Lab Filter Design Directions: Please answer BOTH of the questions and respond to a minimum of two of your classmates. Question A Discuss the various compromises that mus ...

1given the following transfer function modelsy1su1s g11s

1. Given the following transfer function models: y 1 (s)/u 1 (s) = g 11 (s) = 2/(s+3) y 1 (s)/u 2 (s) = g 12 (s) = -1/(s+1) y 2 (s)/u 1 (s) = g 21 (s) = -1/(s+7) y 2 (s)/u 2 (s) = g 22 (s) = 0.5/(s+4) a) Draw the 2x2 ope ...

Telecommunications engineering assignmenttopic fixed

Telecommunications engineering assignment Topic: Fixed wireless broadband internet access Introduction 1. Definition 2. How it work 3. Highspeed internet chioces : DSL , 4G wireless call phone internet. Theard point writ ...

Problem 1a router is used to cut locating notches on a

Problem 1 A router is used to cut locating notches on a printer circuit board. The vibration level at the surface of the board as it is cut, is considered to be a major source of dimensional variation (lower the better) ...

Assignmentfor the circuit below perform the following1given

Assignment For the circuit below, perform the following: 1. Given an AC input voltage of Vrms = 200Vrms and a sinusoidal frequency of omega = 120pi rad/sec, determine the following: o V1peak (peak value of AC input volta ...

Exercise 1charity is a big business in the united states

Exercise 1 Charity is a big business in the United States. The Web site charitynavigator.com gives information on roughly 5500 charitable organizations, and there are many smaller charities that fly below the navigator's ...

1 purposethe primary purpose of this project is to help you

1. Purpose The primary purpose of this project is to help you understand the pipelining process for a simple set of MIPS instructions. You will gain experience with basic pipelining principles, as well as the hazard cont ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen