Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

1. describe the martensite which is formed in maraging steels with martensite which is formed in carbon steels.

2. prepare down the major strength mechanism in high strength aluminum alloys.

3. prepare down the effect of chromium and molybdenum in low alloy steels.

4. Describe the purpose of magnesium treatment in producing S.G. iron.

5. What do you mean by stainless steel? Describe in detail.

6. prepare down the types of stainless steel.

7. What do you mean by HSLA steel?

8. What are the types of cast irion?

9. prepare down the significant copper alloys.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M912027

Have any Question? 


Related Questions in Other Engineering

Stting up a xilinx project for the bcd clockobjective

Setting up a Xilinx project for the BCD Clock Objective: This document is intended to be used as a reference guide to aid in setting up and working with a Xilinx ISE WebPACK project for use with the BCD clock project. Pr ...

I need a report on what is a robot and also discuss seven

I need a report on what is a robot and also discuss seven criteria of defining a robot ( using the book robot programming a guide of programming autonomous robots) I need 4 pages not including references.

Power flow project -figure 1 shows a single-line diagram of

Power Flow Project - Figure 1 shows a single-line diagram of a five-bus power system. Input data are given in Tables 1, 2, and 3. As shown in Table 1, bus 1 is the swing bus, to which a generator is connected. Bus 3 is a ...

Microprocessors projectoverviewyou are required to complete

MICROPROCESSORS PROJECT Overview You are required to complete a final project for this course. It requires you to build a fully functional prototype of a standalone gadget which will be an alarm clock and will also displ ...

Electronics lab transistor biasing1given a bjt unloaded

Electronics Lab: Transistor Biasing 1. Given a BJT unloaded amplifier shown in figure 1 below with β=100. o Draw DC equivalent circuits of this unloaded amplifier. o Draw the DC load line of the circuit. o Determine the ...

Problem 1nbspnbspnbspa letnbsphand calculate ab a-b ab ba

Problem 1:    (a) Let  Hand calculate A+B, A-B, AB, BA, CA, CB, and AC T . (b) Use MATLAB to verify your calculations. Problem 2: (a) Let Hand calculate |A|, r A , and A -1 if it exists. (b) Hand calculates the eigenvalu ...

1the emf of a generator of 377 ohm internal impedance is a

1. The EMF of a generator of 377 ohm internal impedance is a 2 ps long pulse of 12 volt amplitude. The generator drives a 10km long section of transmission line of 377 ohm characteristic impedance and 3 x 10 8 m/s propag ...

1 your boss wants to modify an aircraft by stretching the

1. Your boss wants to modify an aircraft by stretching the fuselage, but only forward of the cg, by a length al. The fuselage has a circular cross section of diameter d. Estimate how much you need to increase the planfor ...

Design a voltage-divider biased common source amplifier

Design a voltage-divider biased common source amplifier with no bypass(JFET) Design a voltage-divider biased common source amplifier with no bypass to the following specifications: Av (overall) = -3, Rsrc = 30 kΩ, Rin = ...

1 for a 77t truck with gross vehicle weight gvw of 136078

1. For a 77t truck with Gross Vehicle Weight (GVW) of 136078 kg with dual rear tyres and a tyre inflation pressure is 120 psi (or 8.43 kg/cm 2 ). Use the equivalent single tyre loading. i. Determine the contact surface a ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen