Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Other Engineering Expert

problem 1) describe the DENSITY OR NEUTRON LOG with reference to principles, Tools, log representation, units of measurement, calibration, environmental effects and applications.

problem 2)a) Describe the physical principle of Litho-Density Tool.

b) describe the environmental effects on the modern Induced Gamma Ray spectra spectrometry.

problem 3) Describe why and how modern BHC sonic tool was developed adding a note on derivation of Wyllie’s formula for porosity.

problem 4) prepare short notes on:

a) Porosity and gas indications from TDT log.

b) Elastic parameters from sonic logs.

c) Cement Bonds Log (CBL).

d) Schlumberger Litho-Density Tool.

e) Attenuation of Sonic wave in cased hole.

problem 5) Describe the measurement technique of EPT log and add a note on its applications.

problem 6) describe the principles of Nuclear Magnetic Log and add a note on its method of measurements.

problem 7) describe the following:

a) Gas detection from overlays.

b) Quantitative interpretation of acoustic images.

c) Borehole Televiewer Tool.

d) Depth of Investigation and vertical resolution of EPT log.

e) Uses of different cross-plots

problem 8) prepare detail notes on the following:

a) Proton Precession magnetometer.

b) Eh-pH as the exploration tool.

c) Distinguish between surface and body waves.

d) Poisson’s ratio and its importance.

e) Tidal correction in gravity method.

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M95343

Have any Question? 


Related Questions in Other Engineering

1given the following transfer function modelsy1su1s g11s

1. Given the following transfer function models: y 1 (s)/u 1 (s) = g 11 (s) = 2/(s+3) y 1 (s)/u 2 (s) = g 12 (s) = -1/(s+1) y 2 (s)/u 1 (s) = g 21 (s) = -1/(s+7) y 2 (s)/u 2 (s) = g 22 (s) = 0.5/(s+4) a) Draw the 2x2 ope ...

Problem 1a router is used to cut locating notches on a

Problem 1 A router is used to cut locating notches on a printer circuit board. The vibration level at the surface of the board as it is cut, is considered to be a major source of dimensional variation (lower the better) ...

This homework is part of a private kaggle competition in

This homework is part of a private Kaggle competition, in the end we only want to submit an excel file with ID and Expected column, and I need the R code as well to submit. I am attaching the data files, both should be u ...

Electronics lab transistor biasingdiscuss what transistor

Electronics Lab: Transistor Biasing Discuss what "transistor biasing" means and its importance to transistor circuit design. Choose one type of biasing, and explain either how it works or its advantages and disadvantages ...

History of architecture and urbanismpick five questions

History of Architecture and Urbanism PICK FIVE QUESTIONS TOTAL TO BE ANSWERED: Each answer must be 150 to 400 words. To be typed, not hand­written. Email your final exam to your discussion leader. 1. The concept of "mode ...

1 your boss wants to modify an aircraft by stretching the

1. Your boss wants to modify an aircraft by stretching the fuselage, but only forward of the cg, by a length al. The fuselage has a circular cross section of diameter d. Estimate how much you need to increase the planfor ...

Time managementdiscuss some of the reasons why individuals

Time Management Discuss some of the reasons why individuals routinely over-estimate the time for project activities. How is this behavior detrimental to the schedule and project? Are some of these reasons more prevalent ...

Project proposal -objectives to get more familiar with the

Project Proposal - Objectives: To get more familiar with the Hadoop Ecosystem (Spark specifically) and Scala Programming. Resources: Files of tweets about election Project Topic: The election of 2016 seems to be a very c ...

Ac models1the impedance of a capacitor is inversely

AC Models 1. The impedance of a capacitor is inversely proportional to the frequency and the capacitor effectively blocks dc voltage. a. True b. False 2. A coupling capacitor couples an ac signal into an amplifier withou ...

Part -1chapter 1 - introduction introduce the project

Part -1: CHAPTER 1 - Introduction: Introduce the project problem; define the scope, aim and objectives of the investigations. CHAPTER 2 - Literature Review: Describe the literature/ theory reviewed which are relevant to ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen