Assignment

Part 1

• Op-Amp Introduction

1. Read Chapters 1-2 in the text Op Amps for Everyone Fourth Edition
2. For the configuration below:

3.

o With Vin = 4Vrms, f = 1kHz answer the following for each case:
o Calculate voltage gain with RF = 1kohm, RG = 5kohm
o Calculate voltage gain with RF = 1kohm, RG = 1kohm
o Calculate voltage gain with RF = 5kohm, RG = 1kohm
o Calculate voltage gain with RF = 5kohm, RG = 5kohm
o Describe the effect of on voltage gain of keeping RF constant and increasing or decreasing RG
o Describe the effect of on voltage gain of keeping RG constant and increasing or decreasing RF

4. For the configuration below

o With Vin = 5Vrms, f = 1kHz answer the following for each case:
o Calculate voltage gain with RF = 1kohm, RG = 5kohm
o Calculate voltage gain with RF = 1kohm, RG = 1kohm
o Calculate voltage gain with RF = 5kohm, RG = 1kohm
o Calculate voltage gain with RF = 5kohm, RG = 5kohm
o Describe the effect of on voltage gain of keeping RF constant and increasing or decreasing RG
o Describe the effect of on voltage gain of keeping RG constant and increasing or decreasing RF
o What does the negative sign in the voltage gain formula indicate?

5. For the configuration below:

o With V1 = 5Vrms, V2 = 4Vrms, VN = 2Vrms, R1 = 1kohm, R2 = 2kohm, RN = 3kohm, RF = 5kohm answer the following:
o Calculate Vout

6. For the configuration below:

o With V1 = 5Vrms, V2 = 4Vrms, R1 = 1kohm, R2 = 2kohm, R3 = 3kohm, R4 = 5kohm answer the following:
o Calculate Vout

7. Include all calculations in a Word document with the title: "HW1_StudentID", with your student id substituted in the file name. Show all work for full credit.

8. Upload file "HW1_StudentID"

Part 2: Lab "Op-Amp Introduction"

Analog Integrated Circuits & Lab

Op-Amp Introduction

The purpose of this lab is to gain familiarity with using Multisim to construct and simulate the noninverting op amp, inverting op amp, adder, and differential amplifier circuits presented in the module. The effect of external biasing resistors will be demonstrated and calculations of output voltage performed in the homework will be confirmed. This lab will set the stage for the concept of confirming calculations with simulation software for the remainder of the course.

Watch video Week 1 - Op-Amp Introduction.- https://content.grantham.edu/at/EE332/Week_1_Op_Amp_Introduction.mp4

Design the Op-Amp configurations from the W1 Assignment "Op-Amp Introduction" in Multisim.

For Non-Inverting Op-Amp:

1. Analyze the non-inverting Op-Amp circuit to calculate the voltage gain Vout/Vin.

A. Design a non-inverting Op-Amp with 5% resistor tolerances for RF and RG in Multisim.
B. Run the simulation to measure the voltage gain Vout/Vin of the amplifier.
C. Complete the table below:

C. Answer the following questions:

2. Does the measured values match the calculated values? If not, explain why they are different?

a. From your measurements, explain how increase in RG affects the voltage gain? Also, explain howincrease in RF affects the voltage gain?
b. What is the effect of resistor tolerance the voltage gain?

3. For Inverting Op-Amp:

Analyze the Inverting Op-Amp circuit to calculate the voltage gain Vout/Vin.

A. Design an inverting Op-Amp with 5% resistor tolerances for RF and RG in Multisim.
B. Run the simulation to measure the voltage gain Vout/Vin of the amplifier.
C. Complete the table below:

D. Answer the following questions:

Does the measured values match the calculated values? If not, explain why they are different?

a. From your measurements, explain how increase in RG affects the voltage gain? Also, explain how increase in RF affects the voltage gain?
b. What is the effect of resistor tolerance the voltage gain?

4. For Op-Amp Adder:

Analyze the Op-Amp Adder circuit with R1 = 2 K?, R2 = 2 K?, R3 = 2K? and Rf = 5 K? to calculate the output voltage Vout.

A. Design an Op-Amp Adder with 5% resistor tolerances for R1, R2, R3 and Rf in Multisim.
B. Run the simulation to measure the output voltage Vout. (Voltage at the output terminal of the amplifier)
C. Complete the table below:

E. For each of the above Op-Amps, answer the following questions:

Does the measured values match the calculated values? If not, explain why they are different?

a. Write the expression for Vout of an Op-Amp Adder.
b. From your measurements, explain how input voltages V1, V2 and V3 affect the output voltage?
c. What is the effect of resistor tolerance the output voltage?

5. For Differential Op-Amp:

Analyze the Differential Op-Amp circuit with R1 = 2 K?, R2 = 2 K?, R3 = 2K? and R4 = 5 K? to calculate the output voltage Vout.

A. Design a Differential Op-Amp circuit with 5% resistor tolerances for R1, R2, R3 and R4 in Multisim.
B. Run the simulation to measure the output voltage of the amplifier.
C. Complete the table below:

6. Create a new word document called "Lab1_StudentID.docx" with your GID substituted into the file name.

7. Verify all calculations from analysis and measurements from simulations from steps 3, 4, 5 and 6. Save the results along with the tables and paste the screen captures in the word document. Make sure to answer the questions in each step.

Upload file "Lab1_StudentID" in Blackboard.

Please fill out and use the following Lab Report Template when submitting your lab work.

Please read and follow the guidelines given in the Solutions Template in submitting all of your lab work.