Ask Other Engineering Expert

AIRCRAFT INTERNAL AND EXTERNAL MARKINGS

SMOKING IN AIRCRAFT - Reference: ANO Article 66 and JAR-25.791

Every aircraft registered in the U.K. must have a notice indicating when smoking is prohibited. The notice must be so positioned that is visible to each passenger seated in the aircraft.

FASTEN SEAT BELTS - Reference: ANO Schedule 4 or JAR-25.791

Every aircraft registered in the U.K. in the Transport Category must, if the commander of the aircraft from his own seat is unable to see all of the passengers seats, have a means of indicating to the passengers that the seat belts should be fastened.

EXIT and BREAK-IN MARKINGS - Reference: ANO Article 62 or JAR-25.811

When a Public Transport aircraft registered in the U.K. is carrying passengers, every exit from, and every internal door in the aircraft shall be in working order and, during take-off, landing or any emergency, must be free from obstruction and not fastened by locking or otherwise so as to prevent, hinder or delay its use by passengers.

Every exit from the aircraft must be marked with the words "EXIT" or "EMERGENCY EXIT" in capital letters. Every exit from the aircraft must be marked with the instructions in English and with diagrams to indicate the correct method of opening the exit. The markings must be placed on or near the inside surface of the door or other closure of the exit and, if it is openable from the outside of the aircraft, on or near the exterior surface.

Aircraft above 3600kg MTOM are normally marked on the exterior surface of their fuselage to show the "BREAK-IN" areas, which can, for the purpose of rescue in an emergency, be most readily, and effectively broken into by persons outside the aircraft. In some circumstances, these markings may be omitted, providing authorisation from the C.A.A. has been obtained.

Break-in areas must be rectangular in shape and must be marked by right angled corner markings each arm of which must be 10cm (4") in length along its outer edge and 2.5cm (1") in width. The words "CUT HERE IN EMERGENCY" must be marked across the centre of each break-in area in capital letters.

On aircraft above 5700kg MTOM, every exit intended to be used by passengers in an emergency, must be marked on the exterior of the aircraft by a band not less than 5cm (2") in width, outlining the exit.


(a) Painted or affixed by some other equally permanent means

(b) Be RED in colour and, if the background renders the red colour not easily visible, it must be outlined in WHITE or some other contrasting colour.

(c) Of a colour clearly contrasting with its background

(d) Kept clean and unobscured at all times.

If one, but not more than one, exit from an aircraft becomes inoperative at a place where it is not reasonably practical for it to be repaired or replaced, there is nothing to prevent the aircraft from carrying passengers until it next lands at a place where the exit can be repaired or replaced provided that:

(a) the number of passengers carried and the position of the seats which they occupy is in accordance with arrangements approved by the C.A.A. either in relation to the particular aircraft or class of aircraft; and:

(b) in accordance with the arrangements in (a), the exit is fastened by locking or otherwise, the words "EXIT" or "EMERGENCY EXIT" are covered and the exit is marked with a RED disc at least 23cm (9") in diameter with a horizontal WHITE bar across it bearing the words "NO EXIT" in RED letters.

 

Other Engineering, Engineering

  • Category:- Other Engineering
  • Reference No.:- M9507553

Have any Question?


Related Questions in Other Engineering

Register design a cpu register is simply a row of

Register design A CPU register is simply a row of flip-flops (i.e. SR, JK, T, etc) put side by side in an array to make the size of register required. For example, an 8 bit register has 8 flip-flops side by side for stor ...

A detailed review of spatial modulation and simulation

A Detailed Review of Spatial Modulation and Simulation Learning Outcomes a. Learn how to model mobile communication channels d. Discern knowledge development and directions on the recent advances in 4G to the research pr ...

Mine safety amp environmental engineering assignment -part

Mine Safety & Environmental Engineering Assignment - Part 1 - Questions 1. Occupational health and safety is the primary factor that needs to be considered in the mining industry. Discuss this statement. 2. Define the fo ...

Projectflow processing of liquor in a mineral refining

Project Flow Processing of Liquor in a Mineral Refining Plant The aim of this project is to design a flow processing system of liquor (slurry) in a mineral (aluminum) refining plant. Aluminum is manufactured in two phase ...

Learning outcomes evaluate multiuser communication and

Learning Outcomes Evaluate multiuser communication and resource sharing techniques; Apply the techniques of, and report on, digital communication applications using Matlab and hardware devices. Assignment Description The ...

Operations engineering assignment -please select only one

Operations Engineering Assignment - Please select only one of the following case studies for your assignment: CASE A. Tesla Motors Tesla is an innovative manufacturer that designs, assemble and sells fully electric vehic ...

Select a risk problem from the list below and prepare a

Select a risk problem from the list below and prepare a risk management plan in accordance with AS/NZS ISO 31000:2009. Please ensure that: - Establish the context clearly, in accordance with the Standard; - Define your s ...

Engineering materials term paper assignment -conduct a

ENGINEERING MATERIALS TERM PAPER ASSIGNMENT - Conduct a thorough literature search and write a 15-20 page technical review paper on the evolution of the engineering materials used in the manufacturing of any one of the f ...

Task 1using the lab kit design a circuit for the processor

Task 1: Using the lab kit, design a circuit for the processor to control the output of a connected 7-segment LED display device. You will be provided with a standard common anode 7-segment display of the type FND-507 (or ...

Control theory - lab reportsfor experiments 1 to 4 you must

Control Theory - Lab Reports For experiments 1 to 4 you must undertake the following: a) At the start of each section (including the pre-lab activities) there are a number learning outcomes. That is, what students should ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As